how to fix my Honda Accord 9th Generation (2013-2017) brake pedal going to the floor

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

critical

Severity

4 min read

605 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the brake pedal going to the floor in a 2013-2017 Honda Accord. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is securely supported on jack stands before working underneath.
•Always wear safety glasses when working on brake systems to protect against fluid splashes.

Symptoms

•Brake pedal feels soft or spongy
•Brake warning light illuminated on the dashboard
•Reduced braking effectiveness
•Fluid leaking under the vehicle
•Air hissing sound when pressing the brake pedal

Diagnostic Steps

1
Inspect brake fluid level in the master cylinder reservoir.
2
Check for any visible leaks in brake lines, calipers, and wheel cylinders.
3
Examine brake pads and rotors for wear and damage.
4
Perform a brake fluid pressure test to check for system integrity.
5
Use a vacuum gauge to test for air in the brake lines.
6
Scan for any error codes using an OBD-II scanner related to the braking system.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Brake fluid
•Funnel
•Brake bleeder kit
•Wrench set
•Flashlight
•Jack and jack stands
•Socket set
•Torque wrench

Parts Required

•Brake fluid (DOT 3 or DOT 4)
•Replacement brake lines (if leaks are found)
•Brake pads (if worn)
•Brake rotors (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake fluid level in the master cylinder reservoir.
2
Check for any visible leaks in brake lines, calipers, and wheel cylinders.
3
Examine brake pads and rotors for wear and damage.
4
Perform a brake fluid pressure test to check for system integrity.
5
Use a vacuum gauge to test for air in the brake lines.
6
Scan for any error codes using an OBD-II scanner related to the braking system.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Disconnect the negative battery terminal to ensure safety.
Place the vehicle on a level surface and engage the parking brake.

2. Check and Refill Brake Fluid

Tools Required: Brake fluid, funnel.
Sub-steps:
1. Locate the brake master cylinder reservoir.
2. Remove the cap and check fluid level; add brake fluid if it's low (use DOT 3 or DOT 4 fluid as specified in the owner's manual).
3. Reinstall the cap securely.

3. Inspect Brake Lines for Leaks

Tools Required: Wrench set, flashlight.
Sub-steps:
1. Visually inspect brake lines for cracks, corrosion, or leaks.
2. Tighten any loose fittings or connections.
3. Replace any damaged brake lines with new ones.

4. Bleed the Brake System

Tools Required: Brake bleeder kit, wrench, brake fluid.
Sub-steps:
1. Start with the wheel farthest from the master cylinder (usually the right rear).
2. Attach the brake bleeder kit to the brake bleeder valve on the caliper.
3. Open the valve and have an assistant press the brake pedal slowly until fluid flows without bubbles.
4. Close the valve before the pedal is released; check fluid level in the master cylinder frequently.
5. Repeat the process for all wheels in the order: right rear, left rear, right front, left front.

5. Inspect and Replace Brake Components (if necessary)

Tools Required: Jack and jack stands, socket set, torque wrench.
Sub-steps:
1. Remove the wheel and inspect brake pads and rotors for excessive wear.
2. If pads are worn below the minimum thickness, replace them with new ones.
3. If rotors are warped or damaged, replace them as well.
4. Reinstall wheels and torque to manufacturer specifications.