how to change the brake pads on a Honda Accord 9th Generation (2013-2017)

Honda Accord Eleventh Generation (2023-present)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

4 min read

603 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Step-by-step guide on how to change brake pads on a Honda Accord 9th Generation (2013-2017). Includes symptoms, diagnostic steps, tools, and safety tips.

Affected Component

Brakes

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is securely supported on jack stands before working underneath it.
•Allow brakes to cool before working on them to avoid burns.

Symptoms

•Squeaking or squealing noise when braking
•Grinding noise indicating metal-to-metal contact
•Reduced braking effectiveness
•Vibration or pulsation during braking
•Warning light on the dashboard (if equipped)

Diagnostic Steps

1
Inspect the brake pads visually for wear indicators.
2
Measure the thickness of the brake pads using a caliper.
3
Check the brake rotor surface for grooves or scoring.
4
Test the brake fluid level and condition.
5
Listen for unusual noises during a slow-speed brake test.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•C-clamp or brake caliper tool
•Bungee cord or wire

Parts Required

•New brake pads
•Brake grease

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Gather all necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Place wheel chocks behind the rear wheels for safety.

2. Remove the Wheel

Tools Required: Socket set
Loosen the lug nuts while the wheel is still on the ground.
Lift the vehicle using a jack and secure it on jack stands.
Remove the lug nuts completely and take off the wheel.

3. Access the Brake Caliper

Tools Required: Socket set, Torque wrench
Locate the brake caliper and remove the caliper mounting bolts (usually two bolts).
Carefully slide the caliper off the rotor and hang it using a bungee cord or wire to avoid stress on the brake line.

4. Remove Old Brake Pads

Remove the old brake pads from the caliper bracket.
Inspect the caliper bracket for debris or rust and clean if necessary.

5. Compress the Caliper Piston

Tools Required: C-clamp or brake caliper tool
Place the old brake pad against the caliper piston and use the C-clamp to gently compress the piston back into the caliper housing until fully retracted.

6. Install New Brake Pads

Place the new brake pads into the caliper bracket, ensuring they are seated properly.
Apply brake grease to the back of the pads to minimize noise.

7. Reassemble the Brake Caliper

Slide the caliper back over the new pads and rotor.
Reinstall the caliper mounting bolts and tighten to manufacturer specifications (typically around 25-35 ft-lbs).

8. Reinstall the Wheel

Place the wheel back on the hub and hand-tighten the lug nuts.
Lower the vehicle off the jack stands and then fully tighten the lug nuts in a crisscross pattern to the manufacturer's torque specification (usually 80-100 ft-lbs).

9. Final Check

Pump the brake pedal several times to ensure the caliper piston is properly seated against the new pads.
Check the brake fluid level and top off if necessary.