why does my Honda Accord Eleventh Generation (2023-present) engine light come on after oil change

Honda Accord 11th Gen (2023-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

557 words

Problem Statement

Learn why the check engine light comes on after an oil change in Honda Accord (2023-present) and how to diagnose and fix the issue.

Affected Component

Engine

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the engine to cool before opening the oil system to prevent burns.

Symptoms

•Check engine light illuminated
•Oil pressure warning light may appear
•Engine may exhibit rough idle
•Unusual engine noises may be heard
•Decreased fuel efficiency
•Oil leak observed under the vehicle

Diagnostic Steps

1
Scan the vehicle's OBD-II system for error codes using a diagnostic scanner.
2
Check oil level and condition using the dipstick to ensure proper oil quantity and quality.
3
Inspect the oil filter for signs of a poor seal or failure.
4
Verify that the correct oil type and viscosity were used during the oil change.
5
Look for any loose or disconnected sensors or hoses around the engine bay.
6
Examine the engine for any visible oil leaks or other damage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Oil filter wrench
•Oil catch pan

Parts Required

•Oil filter
•Engine oil (0W-20 or as specified in the owner’s manual)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's OBD-II system for error codes using a diagnostic scanner.
2
Check oil level and condition using the dipstick to ensure proper oil quantity and quality.
3
Inspect the oil filter for signs of a poor seal or failure.
4
Verify that the correct oil type and viscosity were used during the oil change.
5
Look for any loose or disconnected sensors or hoses around the engine bay.
6
Examine the engine for any visible oil leaks or other damage.

Solution

1. Preparation

Tools Required: OBD-II scanner, socket set, torque wrench, oil filter wrench, oil catch pan.
Ensure the engine is cool before starting work.
Disconnect the battery to prevent electrical shorts during inspection.

2. Check Oil Level and Quality

Sub-steps:
1. Remove the dipstick and wipe it clean.
2. Reinsert the dipstick fully and remove it again to check the oil level.
3. Inspect the oil’s color and texture; it should be amber and smooth, not gritty or milky.
If oil is low or dirty, add the correct type of oil or perform another oil change.

3. Inspect Oil Filter

Sub-steps:
1. Using an oil filter wrench, remove the oil filter.
2. Inspect the rubber O-ring for damage or debris.
3. Replace the oil filter if it shows signs of wear or if the O-ring was not properly seated.
4. Install a new oil filter, ensuring it's tightened to the manufacturer's specifications.

4. Verify Engine Oil Type

Sub-steps:
1. Cross-check the owner’s manual for the recommended oil type (e.g., 0W-20).
2. If the incorrect oil was used, drain the oil and replace it with the correct type.

5. Reconnect Battery and Clear Codes

Sub-steps:
1. Reconnect the battery terminals securely.
2. Use the OBD-II scanner to clear any stored error codes.
3. Start the engine to monitor if the check engine light remains off.