why does my Honda Accord make a grinding noise when turning

Honda Accord 10th Generation (2018-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

563 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix grinding noise when turning in Honda Accord. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely supported on jack stands before working underneath.

Symptoms

•Grinding noise when making turns
•Difficulty in steering or increased resistance
•Vibration in the steering wheel
•Uneven tire wear
•Possible clunking sound in addition to grinding

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage to the CV joints or axles.
3
Examine the wheel bearings for signs of wear or damage.
4
Inspect the suspension components, including struts and bushings.
5
Test drive the vehicle to replicate the noise and determine if it changes with speed or turning angle.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Jack and jack stands
•Bearing puller
•Torque wrench
•Power steering fluid

Parts Required

•CV joint or axle (if damaged)
•Wheel bearings (if worn)
•Suspension components (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage to the CV joints or axles.
3
Examine the wheel bearings for signs of wear or damage.
4
Inspect the suspension components, including struts and bushings.
5
Test drive the vehicle to replicate the noise and determine if it changes with speed or turning angle.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is turned off.
Disconnect the battery to avoid any electrical issues.

2. Check and Refill Power Steering Fluid

Open the hood and locate the power steering reservoir.
If the fluid level is low, use a funnel to add the recommended power steering fluid until it reaches the proper level.
Inspect the reservoir for leaks.

3. Inspect and Replace CV Joints or Axles

Elevate the front of the vehicle using a jack and secure it with jack stands.
Remove the front wheels using a socket set.
Inspect the CV boots for tears or leaks. If damaged, proceed to replace the CV joint or axle.
- Sub-steps:
  - Remove the axle nut and any retaining clips.
  - Disconnect the lower control arm if necessary.
  - Pull the axle out of the transmission and replace it with a new one.
  - Reassemble in reverse order and torque the axle nut to the manufacturer's specifications.

4. Check and Replace Wheel Bearings

With the wheels removed, grasp the wheel hub and check for play.
If loose, remove the hub and replace the wheel bearing.
- Sub-steps:
  - Use a bearing puller to remove the old bearing.
  - Install the new bearing using a press or appropriate tool.
  - Reattach the hub and wheels, torquing all bolts to specification.

5. Inspect and Replace Suspension Components

Inspect struts, shocks, and bushings for wear.
Replace any damaged components.
- Sub-steps:
  - Remove the strut assembly from the vehicle.
  - Replace the strut or shock absorber using a spring compressor if necessary.
  - Reinstall the assembly and torque all bolts to the specified values.