why does my Honda Accord jerk when I accelerate

Honda Accord 10th Generation (2018-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

537 words

Problem Statement

Learn how to diagnose and fix jerking during acceleration in Honda Accord. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to avoid short circuits.

Symptoms

•Jerking or hesitation during acceleration
•Check engine light illuminated
•Poor fuel economy
•Unusual engine noises (e.g., knocking or whining)
•Rough idle when at a stop

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the transmission fluid level and condition; check for contamination or burning smell.
3
Check the condition of spark plugs and ignition coils for wear or damage.
4
Inspect fuel system components, including fuel filter and fuel pump operation.
5
Examine the air intake system for blockage or leaks, especially in the vacuum lines.
6
Test the throttle position sensor (TPS) for proper voltage and response.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Flathead screwdriver
•Fuel pressure gauge
•Safety glasses
•Transmission fluid dipstick
•Multimeter

Parts Required

•Spark plugs
•Ignition coils
•Fuel filter
•Transmission fluid
•Throttle position sensor (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the transmission fluid level and condition; check for contamination or burning smell.
3
Check the condition of spark plugs and ignition coils for wear or damage.
4
Inspect fuel system components, including fuel filter and fuel pump operation.
5
Examine the air intake system for blockage or leaks, especially in the vacuum lines.
6
Test the throttle position sensor (TPS) for proper voltage and response.

Solution

1. Preparation

Gather tools and parts needed before starting the repair.
Disconnect the battery to ensure safety while working on electrical components.

2. Address Ignition Issues

Tools Required: Socket set, torque wrench, flathead screwdriver.
Remove the engine cover if applicable.
Remove the ignition coils: Disconnect the electrical connectors and unbolt them.
Inspect spark plugs: Use a spark plug socket to remove each spark plug and check for wear.
Replace any faulty spark plugs and ignition coils as necessary, ensuring they are properly torqued to manufacturer specifications.

3. Fuel System Inspection

Tools Required: Fuel pressure gauge, socket set, safety glasses.
Check the fuel filter: Locate and remove the fuel filter, examining for clogging or debris.
If needed, replace the fuel filter with a new one, ensuring correct alignment and secure fittings.
Test the fuel pump operation using the fuel pressure gauge; compare readings to manufacturer specifications.

4. Transmission Fluid Check

Tools Required: Transmission fluid dipstick, funnel.
Check the transmission fluid level using the dipstick; top off with the appropriate type of transmission fluid if low.
If the fluid is dark or has a burnt smell, consider a transmission fluid change.

5. Throttle Position Sensor Adjustment

Tools Required: Multimeter, screwdriver.
Remove the TPS from the throttle body.
Using a multimeter, check the resistance across the terminals while slowly moving the throttle plate. The readings should change smoothly.
If the TPS is faulty, replace it and ensure it is properly calibrated.