what to do if GMC Sierra T1XX (2019-Present) traction control light is on?

GMC Sierra T1XX (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

535 words

Problem Statement

Learn how to diagnose and fix the traction control light issue in GMC Sierra T1XX (2019-Present). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the vehicle to cool before inspecting brake components.

Symptoms

•Traction control warning light illuminated on the dashboard
•Reduced vehicle stability during acceleration or cornering
•Unusual sounds from the ABS system during operation
•Poor acceleration or loss of power
•Check engine light may also be illuminated

Diagnostic Steps

1
Scan the vehicle's OBD-II system for any diagnostic trouble codes (DTCs) using an OBD-II scanner.
2
Inspect the wheel speed sensors for damage, dirt, or disconnection.
3
Check the brake fluid level and inspect for any leaks in the brake system.
4
Examine the ABS control module for signs of corrosion or electrical issues.
5
Test the traction control switch for proper operation.
6
Verify that there are no issues with the vehicle's tires, such as uneven wear or incorrect pressure.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench
•Screwdrivers (flathead and Phillips)

Parts Required

•Wheel speed sensors (if replacement is needed)
•Traction control switch (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's OBD-II system for any diagnostic trouble codes (DTCs) using an OBD-II scanner.
2
Inspect the wheel speed sensors for damage, dirt, or disconnection.
3
Check the brake fluid level and inspect for any leaks in the brake system.
4
Examine the ABS control module for signs of corrosion or electrical issues.
5
Test the traction control switch for proper operation.
6
Verify that there are no issues with the vehicle's tires, such as uneven wear or incorrect pressure.

Solution

1. Preparation

Gather tools and parts required.
Ensure the vehicle is parked on a level surface and turn off the ignition.
Disconnect the battery to prevent electrical shorts.

2. Inspect Wheel Speed Sensors

Locate the wheel speed sensors at each wheel hub.
Remove any dirt or debris around the sensor area.
Disconnect the sensor wiring harness and check for corrosion.
If the sensor appears damaged, replace it with a new one.
Reconnect the sensor and ensure it is securely fastened.

3. Check ABS Control Module

Locate the ABS control module, typically found near the brake master cylinder.
Inspect the wiring harness for any signs of wear or damage.
Use a multimeter to check for voltage at the connector while the ignition is on.
If there is no voltage, repair the wiring or replace the ABS control module if necessary.

4. Test Traction Control Switch

Locate the traction control switch on the dashboard.
Remove the switch from the dashboard to access the wiring.
Test the switch continuity using a multimeter; replace it if defective.

5. Reconnect Battery and Clear Codes

Reconnect the battery terminals securely.
Use the OBD-II scanner to clear any fault codes from the system.
Start the vehicle and check if the traction control light remains off.