FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
GMC Sierra T1XX (2019-Present) AC not blowing cold air how to troubleshoot - GMC Sierra
Home/Cars/GMC/Sierra/T1XX (2019-Present)/GMC Sierra T1XX (2019-Present) AC not blowing cold air how to troubleshoot

GMC Sierra T1XX (2019-Present) AC not blowing cold air how to troubleshoot

GMC Sierra T1XX (2019-Present)

Error Codes
2-4 hours
Time
medium
Difficulty
medium
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
3 min read
528 words

Problem Statement

Learn how to troubleshoot and fix AC not blowing cold air in GMC Sierra T1XX. Step-by-step guide with diagnostic steps and repair instructions.

Affected Component
HVAC
Estimated Time
2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

  • •Disconnect the battery before working on electrical components.
  • •Allow the engine to cool before servicing the AC system.

Symptoms

  • •AC system blowing warm air
  • •AC compressor not engaging
  • •Unusual noises coming from the AC compressor
  • •Increased humidity inside the cabin
  • •Foul odor when AC is turned on

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •OBD-II scanner
  • •Refrigerant manifold gauge set
  • •Vacuum pump
  • •Socket set
  • •Torque wrench

Parts Required

  • •Refrigerant (R-134a or R-1234yf)
  • •AC compressor (if required)
  • •AC condenser (if required)
  • •O-ring seals

Additional Information

Affected Component
HVAC
Estimated Time
2-4 hours
Difficulty
medium
Severity
medium
Tools Required
5 items
Parts Required
4 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation
Solution
1. Preparation
  • Gather tools and parts needed for the repair.
  • Disconnect the vehicle battery to ensure safety during repairs.
2. Recharge AC System
  • Tools Required: Refrigerant manifold gauge set, vacuum pump, refrigerant (R-134a or R-1234yf depending on system).
  • Connect the low-pressure side of the manifold gauge set to the AC service port.
  • Evacuate the system using a vacuum pump for at least 30 minutes to remove moisture and air.
  • Recharge the system with the appropriate amount of refrigerant as specified in the owner's manual.
3. Inspect and Replace AC Compressor
  • Tools Required: Socket set, torque wrench, AC compressor replacement, O-ring seals.
  • Remove the drive belt from the AC compressor.
  • Disconnect the electrical connector and the refrigerant lines from the compressor.
  • Unbolt the compressor from its mounting bracket and remove it.
  • Install the new compressor with new O-ring seals, ensuring proper torque specifications are followed.
  • Reconnect the refrigerant lines and electrical connector.
4. Replace AC Condenser (if needed)
  • Tools Required: Socket set, AC condenser, refrigerant recovery system.
  • Remove the front grille and any panels obstructing access to the condenser.
  • Disconnect the refrigerant lines from the condenser and unbolt it from its mounting points.
  • Install the new condenser and reconnect the refrigerant lines, ensuring no leaks.
  • Reassemble any removed components.