why does my Genesis G70 IG (2017-2023) make a clicking sound when turning?

Genesis G70 IG (2017-2023)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

506 words

Problem Statement

Learn how to diagnose and fix the clicking sound when turning in Genesis G70 (2017-2023). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely lifted before working underneath.

Symptoms

•Clicking or popping noise when turning the steering wheel
•Increased noise when making sharp turns
•Vibration felt through the steering wheel
•Difficulty in steering, particularly during low-speed maneuvers
•Potential clunking sound during acceleration or deceleration

Diagnostic Steps

1
Inspect the CV joint boots for any tears or leaks.
2
Check for play in the wheel bearings by lifting the front of the vehicle and shaking the wheel.
3
Examine the suspension components, including control arms and bushings, for wear or damage.
4
Test drive the vehicle while listening for the sound to determine if it changes with speed or direction.
5
Scan the vehicle for any error codes that may indicate electronic steering issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•CV joint puller
•Grease
•Safety glasses
•Gloves

Parts Required

•CV joint (if damaged)
•CV joint grease
•Wheel bearing (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joint boots for any tears or leaks.
2
Check for play in the wheel bearings by lifting the front of the vehicle and shaking the wheel.
3
Examine the suspension components, including control arms and bushings, for wear or damage.
4
Test drive the vehicle while listening for the sound to determine if it changes with speed or direction.
5
Scan the vehicle for any error codes that may indicate electronic steering issues.

Solution

1. Preparation

Gather tools and parts.
Ensure the vehicle is on a level surface and securely lifted using jack stands.
Disconnect the battery to ensure safety while working on electrical connections.

2. Inspect and Replace CV Joints

Tools Required: Socket set, torque wrench, CV joint puller, grease, safety glasses, gloves.
Remove the wheel from the affected side by loosening the lug nuts and using a socket set.
Remove the axle nut with a socket wrench and puller if necessary.
Disconnect the lower control arm from the steering knuckle.
Carefully slide the CV joint out of the transmission or differential housing.
Inspect the CV joint for wear or damage; if necessary, replace it with a new CV joint.
- Installation: Apply grease to the new CV joint, insert it back into the housing, and reassemble the components in reverse order.
Torque the axle nut to the manufacturer’s specifications (refer to the service manual for exact torque value).

3. Inspect and Replace Wheel Bearings (if necessary)

If play is detected in the wheel bearings, remove the hub assembly.
Use a bearing puller to remove the old bearing.
Clean the mounting area and install the new bearing, making sure it is seated properly.
Reassemble the hub and torque all fasteners to specifications.