how to troubleshoot a Genesis G70 IG (2017-2023) that won't start

Genesis G70 IG (2017-2023)

Error Codes

1-3 hours

Time

medium

Difficulty

high

Severity

3 min read

545 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to troubleshoot and fix a no-start condition in Genesis G70 (2017-2023). Step-by-step guide with diagnostic steps and repair instructions.

Affected Component

Electrical

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Avoid touching positive and negative terminals simultaneously to prevent short circuits.

Symptoms

•No engine cranking sound
•Dashboard lights illuminate but engine does not start
•Clicking sound from the starter relay
•Battery warning light illuminated
•Possible security system indicator light active

Diagnostic Steps

1
Check the battery voltage using a multimeter; ensure it reads above 12.4 volts.
2
Inspect battery terminals for corrosion or loose connections.
3
Test the starter relay by swapping it with a similar relay in the fuse box.
4
Verify the ignition switch operation by checking for power at the starter solenoid when the key is turned.
5
Scan for any fault codes using an OBD-II scanner to identify potential issues in the engine management system.
6
Inspect fuses related to the starting system for any blown fuses.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Battery terminal cleaner

Parts Required

•Replacement battery (if necessary)
•Starter relay (if faulty)
•Starter motor (if determined to be defective)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the battery voltage using a multimeter; ensure it reads above 12.4 volts.
2
Inspect battery terminals for corrosion or loose connections.
3
Test the starter relay by swapping it with a similar relay in the fuse box.
4
Verify the ignition switch operation by checking for power at the starter solenoid when the key is turned.
5
Scan for any fault codes using an OBD-II scanner to identify potential issues in the engine management system.
6
Inspect fuses related to the starting system for any blown fuses.

Solution

1. Preparation

Gather tools: OBD-II scanner, multimeter, socket set, battery terminal cleaner, replacement parts if needed.
Ensure the vehicle is in a safe, well-ventilated area and disconnect the negative battery terminal to prevent electrical shock.

2. Battery Inspection and Replacement

Sub-step 1: Clean the battery terminals using a battery terminal cleaner or a wire brush.
Sub-step 2: Reconnect the battery terminals securely, ensuring no corrosion remains.
Sub-step 3: If the battery voltage is low (below 12.4 volts), jump-start the vehicle or replace the battery with a new one (ensure the new battery matches manufacturer specifications).

3. Starter Relay and Ignition Switch Check

Sub-step 1: Locate the starter relay in the fuse box, typically under the hood.
Sub-step 2: Remove the relay and inspect for any signs of damage. Swap with a similar relay to test functionality.
Sub-step 3: If the relay is functioning, check the ignition switch by using a multimeter to verify it sends voltage to the starter solenoid when turned to the start position.

4. Starter Inspection

Sub-step 1: If the engine still does not crank, access the starter motor (usually located near the transmission).
Sub-step 2: Disconnect the wiring harness from the starter and check for voltage at the solenoid terminal when the ignition is turned.
Sub-step 3: If there is no voltage, the ignition switch or relay may be faulty; if there is voltage, the starter motor may need replacement.