how to tell if my Genesis G70 IG (2017-2023) needs new shocks?

Genesis G70 IG (2017-2023)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

569 words

Problem Statement

Learn how to determine if your Genesis G70 needs new shocks and follow our step-by-step guide for replacement. Improve your ride quality today!

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands after lifting the vehicle to prevent accidents.

Symptoms

•Excessive bouncing or swaying during driving
•Uneven tire wear
•Increased braking distance
•Oil leakage from the shock absorbers
•Noisy suspension when going over bumps

Diagnostic Steps

1
Inspect the shock absorbers visually for signs of oil leakage or physical damage.
2
Perform a bounce test by pushing down on each corner of the vehicle and observing how it reacts.
3
Check for uneven tire wear patterns that may indicate suspension issues.
4
Test drive the vehicle over various road conditions to assess ride comfort and handling.
5
Measure the distance the vehicle settles after being pushed down during the bounce test.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Lug wrench
•Socket set
•Torque wrench
•Spring compressor

Parts Required

•New shock absorbers (front and/or rear as needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the shock absorbers visually for signs of oil leakage or physical damage.
2
Perform a bounce test by pushing down on each corner of the vehicle and observing how it reacts.
3
Check for uneven tire wear patterns that may indicate suspension issues.
4
Test drive the vehicle over various road conditions to assess ride comfort and handling.
5
Measure the distance the vehicle settles after being pushed down during the bounce test.

Solution

1. Preparation

Gather necessary tools and parts before starting the replacement.
Ensure the vehicle is parked on a level surface and the engine is off.
Tools Required: Jack, jack stands, lug wrench, socket set, torque wrench, and a spring compressor.
Safety Warnings: Always use jack stands after lifting the vehicle to prevent accidents.

2. Remove Wheels

Loosen the lug nuts on the front and rear wheels using the lug wrench.
Lift the vehicle with a jack and securely place jack stands beneath the vehicle.
Remove the lug nuts completely and take off the wheels.

3. Remove Old Shock Absorbers

Locate the upper and lower mounting points of the shock absorber.
Use the socket set to remove the bolts securing the shock absorber to the vehicle.
Carefully pull the shock absorber out from its mounting point. If necessary, use a spring compressor to relieve tension if the shock is part of a strut assembly.

4. Install New Shock Absorbers

Align the new shock absorber with the mounting points and insert it into place.
Hand-tighten the bolts to hold the shock absorber in place.
Use the torque wrench to tighten the bolts to the manufacturer’s specified torque value (consult the service manual for exact specifications).

5. Reinstall Wheels

Place the wheels back onto the wheel hubs.
Hand-tighten the lug nuts, then lower the vehicle from the jack stands using the jack.
Once the vehicle is back on the ground, use the torque wrench to tighten the lug nuts to the manufacturer’s specified torque value.

6. Final Check

Inspect the installation of the new shocks to ensure all bolts are secure.
Perform a bounce test again to verify proper installation and functionality.