how to fix my Genesis G70 IG (2017-2023) key fob not working

Genesis G70 IG (2017-2023)

Error Codes

30 minutes to 1 hour

Time

medium

Difficulty

medium

Severity

3 min read

522 words

Problem Statement

Learn how to diagnose and fix a non-working key fob for Genesis G70 (2017-2023). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Electrical

Estimated Time

30 minutes to 1 hour

⚠️ Safety Warnings

Important safety information - read before proceeding

•Be careful when prying open the key fob to avoid damaging the casing or internal components.

Symptoms

•Key fob buttons unresponsive
•Vehicle does not recognize key fob when attempting to start
•Security light flashing on the dashboard
•Inability to lock or unlock doors remotely
•Weak or no signal from the key fob

Diagnostic Steps

1
Check the battery level of the key fob using a multimeter.
2
Replace the key fob battery with a new one and test its functionality.
3
Inspect the key fob for any visible physical damage or water ingress.
4
Attempt to reprogram the key fob using the vehicle's onboard programming procedures.
5
Use an OBD-II scanner to check for any related error codes that might indicate issues with the vehicle's keyless entry system.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Flathead screwdriver
•Small Phillips screwdriver
•Multimeter

Parts Required

•CR2032 battery

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the battery level of the key fob using a multimeter.
2
Replace the key fob battery with a new one and test its functionality.
3
Inspect the key fob for any visible physical damage or water ingress.
4
Attempt to reprogram the key fob using the vehicle's onboard programming procedures.
5
Use an OBD-II scanner to check for any related error codes that might indicate issues with the vehicle's keyless entry system.

Solution

1. Preparation

Gather necessary tools and parts:
- Tools: Flathead screwdriver, small Phillips screwdriver
- Parts: CR2032 battery (or specific replacement battery for the key fob)
Ensure you are in a well-lit area to work on the key fob.

2. Open the Key Fob

Using the flathead screwdriver, gently pry open the key fob casing at the seam.
Carefully separate the two halves without damaging the clips.

3. Replace the Battery

Remove the old battery from the key fob.
Install the new CR2032 battery, ensuring the positive (+) side is facing up.
Ensure the battery is seated properly in its compartment.

4. Reassemble the Key Fob

Align the two halves of the key fob.
Press them together until they click securely into place. Ensure all clips are engaged.

5. Test the Key Fob

Stand near the vehicle and press the lock and unlock buttons to verify functionality.
If the key fob is still not working, proceed to reprogram it.

6. Reprogram the Key Fob (if necessary)

Enter the vehicle and close all doors.
Insert the key into the ignition and turn it to the "On" position (do not start the engine).
Within 10 seconds, press the lock button on the key fob three times.
Turn the ignition off and remove the key. Test the key fob again.