how to fix AC not blowing cold air in Genesis G70 IG (2017-2023)

Genesis G70 IG (2017-2023)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

4 min read

601 words

Problem Statement

Learn how to diagnose and fix AC not blowing cold air in Genesis G70 (2017-2023). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow the engine and AC system to cool before servicing.

Symptoms

•AC system blowing warm air
•AC compressor not engaging
•Unusual noises coming from the AC unit
•Frost or ice formation on AC lines
•Increased cabin humidity levels

Diagnostic Steps

1
Inspect the AC system for visible leaks or damage.
2
Check the refrigerant level using a gauge set.
3
Scan the vehicle’s computer for any relevant trouble codes using an OBD-II scanner.
4
Verify the operation of the AC compressor by checking its engagement.
5
Test the AC system's electrical components, including fuses and relays.
6
Inspect the cabin air filter for blockages or restrictions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•AC refrigerant gauge set
•Socket set
•Torque wrench
•Screwdrivers
•AC pulley removal tool

Parts Required

•AC refrigerant
•AC compressor (if needed)
•Cabin air filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the AC system for visible leaks or damage.
2
Check the refrigerant level using a gauge set.
3
Scan the vehicle’s computer for any relevant trouble codes using an OBD-II scanner.
4
Verify the operation of the AC compressor by checking its engagement.
5
Test the AC system's electrical components, including fuses and relays.
6
Inspect the cabin air filter for blockages or restrictions.

Solution

1. Preparation

Gather tools and parts required for the repair.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the battery to ensure safety while working on electrical components.

2. Recharge the AC System

Tools Required: AC refrigerant gauge set, refrigerant canister, safety goggles, gloves.
Attach the gauge set to the AC service ports (high and low).
Check the pressure readings; if low, proceed to recharge:
1. Connect the refrigerant canister to the low-pressure port.
2. Open the valve on the canister slowly while monitoring the gauge.
3. Stop when the gauge reaches the manufacturer’s specified pressure.
4. Disconnect the canister and recheck pressures.

3. Replace the AC Compressor (if necessary)

Tools Required: Socket set, torque wrench, screwdrivers, AC pulley removal tool.
Remove the serpentine belt:
1. Locate the belt tensioner and rotate it to release the tension.
2. Remove the belt from the AC compressor pulley.
Disconnect electrical connectors and refrigerant lines from the compressor:
1. Use a line wrench to carefully unscrew the refrigerant lines.
2. Cap the lines to prevent moisture contamination.
Remove the AC compressor from its mounting bracket:
1. Unbolt the compressor using the socket set.
2. Replace with a new compressor, ensuring proper alignment.
3. Torque bolts to manufacturer specifications.
Reconnect refrigerant lines and electrical connectors.

4. Replace the Cabin Air Filter

Tools Required: Screwdriver (if required for access).
Locate the cabin air filter housing, usually behind the glove box:
1. Remove screws or clips securing the glove box if necessary.
2. Pull out the old cabin air filter.
3. Insert the new filter in the correct orientation.
4. Reassemble the glove box.