how to fix a leaking strut on my Genesis G70 IG (2017-2023)?

Genesis G70 IG (2017-2023)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

519 words

Problem Statement

Learn how to fix a leaking strut on your Genesis G70 IG (2017-2023). Step-by-step guide with diagnostic steps, tools required, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under a vehicle.
•Allow the vehicle to cool if it has been running before working on the suspension.

Symptoms

•Noticeable oil leakage around the strut assembly
•Reduced ride comfort and increased bounce
•Unusual noise such as clunking or knocking when driving over bumps
•Uneven tire wear
•Warning light for suspension issues (if applicable)

Diagnostic Steps

1
Inspect the strut for visible signs of oil leakage and damage.
2
Check the condition of the strut mounts and bushings for wear.
3
Measure the ride height of the vehicle to identify any sagging.
4
Perform a bounce test to assess strut performance.
5
Examine surrounding components for damage or misalignment.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Lug wrench
•Jack and jack stands
•Socket set
•Torque wrench
•Safety glasses
•Gloves

Parts Required

•New strut assembly
•Strut mounts (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the strut for visible signs of oil leakage and damage.
2
Check the condition of the strut mounts and bushings for wear.
3
Measure the ride height of the vehicle to identify any sagging.
4
Perform a bounce test to assess strut performance.
5
Examine surrounding components for damage or misalignment.

Solution

1. Preparation

Gather all necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Wear safety glasses and gloves for protection.

2. Remove the Wheel

Use a lug wrench to loosen the lug nuts on the affected wheel.
Lift the vehicle using a jack and secure it with jack stands.
Completely remove the lug nuts and take off the wheel.

3. Remove the Strut Assembly

Disconnect any brake lines or ABS wires attached to the strut (if applicable).
Remove the nuts and bolts securing the strut to the lower control arm and the strut tower.
- Tools Required: Socket set, torque wrench
Carefully lower the strut assembly from the vehicle.

4. Replace the Strut

Install a new strut by reversing the removal process.
- Ensure that the strut is aligned correctly with the mounting holes.
- Hand-tighten the nuts before fully torquing them to the manufacturer's specifications.
Reattach any brake lines or ABS wires that were disconnected.

5. Reinstall the Wheel

Place the wheel back onto the hub and hand-tighten the lug nuts.
Lower the vehicle from the jack stands and remove the jack.
Use a torque wrench to tighten the lug nuts to the specified torque value (usually around 80-100 lb-ft).

6. Final Checks

Inspect the strut for proper installation.
Test drive the vehicle to ensure the repair was successful and check for any leaks.