how to check for strut issues in my Genesis G70 IG (2017-2023)?

Genesis G70 IG (2017-2023)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

557 words

Problem Statement

Learn how to diagnose and fix strut issues in Genesis G70 IG (2017-2023). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is securely raised and supported on jack stands before working underneath.
•Allow the suspension components to settle before reassembling to ensure proper alignment.

Symptoms

•Uneven tire wear
•Excessive bouncing or swaying during driving
•Noisy strut operation (clunking or rattling sounds)
•Poor handling or stability on turns
•Visible fluid leaks on or around strut assemblies

Diagnostic Steps

1
Examine the struts for any signs of physical damage or leaks.
2
Push down firmly on the front or rear of the vehicle and release; the car should bounce once and return to rest.
3
Inspect all tires for uneven wear patterns indicating alignment issues potentially caused by faulty struts.
4
Drive the vehicle over bumps and listen for any unusual sounds emanating from the strut area.
5
Use a wheel alignment tool or take the vehicle to a shop to check for misalignment that may indicate strut problems.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Strut spring compressor

Parts Required

•Replacement struts (if necessary)
•New upper strut mounts (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Examine the struts for any signs of physical damage or leaks.
2
Push down firmly on the front or rear of the vehicle and release; the car should bounce once and return to rest.
3
Inspect all tires for uneven wear patterns indicating alignment issues potentially caused by faulty struts.
4
Drive the vehicle over bumps and listen for any unusual sounds emanating from the strut area.
5
Use a wheel alignment tool or take the vehicle to a shop to check for misalignment that may indicate strut problems.

Solution

1. Preparation

Tools Required:
- Jack and jack stands
- Socket set
- Torque wrench
- Strut spring compressor (if replacing struts)
Ensure vehicle is on a level surface and secure before starting.

2. Remove Wheel

Loosen the lug nuts slightly while the vehicle is on the ground.
Raise the vehicle using a jack and secure it with jack stands.
Remove the lug nuts completely and take off the wheel to access the strut assembly.

3. Inspect and Replace Struts

Inspect Struts:
- Check for leaks, cracks, or any signs of wear.
Replace Struts (if needed):
1. Remove the upper strut mount bolts using a socket.
2. Disconnect any brake line brackets or ABS sensor wires attached to the strut.
3. Remove the lower strut mounting bolts and detach the strut from the steering knuckle.
4. Use the strut spring compressor to safely compress the coil spring.
5. Remove the top nut of the strut assembly and take off the coil spring.
6. Install the new strut by reversing the removal steps, ensuring to follow torque specifications for all bolts.

4. Reassemble and Test

Reattach the wheel and hand-tighten the lug nuts.
Lower the vehicle and torque the lug nuts to the manufacturer's specifications.
Test drive the vehicle to ensure proper handling and check for any noises or issues.