why is my Genesis G70 making a clunking noise when I turn

Genesis G70 1st Gen (2018-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

507 words

Problem Statement

Learn how to diagnose and fix clunking noise when turning in Genesis G70. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under a vehicle.
•Disconnect the battery if working on electrical components.

Symptoms

•Clunking noise when turning the steering wheel
•Noise may vary with speed (louder at low speeds)
•Possible vibration in the steering wheel
•Uneven tire wear
•Loose or wobbly steering feel

Diagnostic Steps

1
Inspect the front suspension components visually for any signs of damage or wear.
2
Check the power steering fluid level and condition.
3
Raise the front of the vehicle and perform a manual inspection of the wheel bearings and CV joints.
4
Test drive the vehicle to confirm the noise occurs under specific conditions.
5
Use a stethoscope or mechanic's tool to pinpoint the source of the noise while turning.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Funnel
•Jack stands

Parts Required

•Control arms, bushings, sway bar links (if damaged)
•Power steering fluid

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front suspension components visually for any signs of damage or wear.
2
Check the power steering fluid level and condition.
3
Raise the front of the vehicle and perform a manual inspection of the wheel bearings and CV joints.
4
Test drive the vehicle to confirm the noise occurs under specific conditions.
5
Use a stethoscope or mechanic's tool to pinpoint the source of the noise while turning.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Allow the engine to cool down if it has been running.

2. Inspect and Replace Worn Suspension Components

Sub-steps:
1. Remove the front wheel using a socket set.
2. Inspect the control arms, bushings, and sway bar links for wear or damage.
3. If any components are found to be worn or damaged, replace them with new parts.
  - Tools Required: Socket set, torque wrench.
  - Specifics: Follow the manufacturer's torque specifications for reinstallation.

3. Check and Refill Power Steering Fluid

Sub-steps:
1. Locate the power steering fluid reservoir.
2. Remove the cap and check the fluid level; add manufacturer-recommended power steering fluid if low.
3. Start the engine and turn the steering wheel from lock to lock to help circulate the fluid.
  - Tools Required: Funnel, power steering fluid.

4. Inspect CV Joints and Wheel Bearings

Sub-steps:
1. With the vehicle raised, turn the wheels by hand to check for any clicking or clunking noises from the CV joints.
2. Grasp the wheel at the 12 and 6 o'clock positions and check for play to assess wheel bearing condition.
3. If a CV joint is damaged or the wheel bearing is loose, replace them as necessary.
  - Tools Required: Jack stands, socket set, hammer.
  - Specifics: Ensure to torque wheel bearings to the manufacturer’s specifications.