why does my Genesis G70 shake when I brake hard?

Genesis G70 1st Gen (2018-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

516 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix shaking during hard braking in Genesis G70. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always allow the vehicle to cool before working on the brakes.
•Ensure the vehicle is securely supported on jack stands before working underneath.

Symptoms

•Shaking or vibration felt in the steering wheel during hard braking
•Pulsating brake pedal when applying brakes
•Uneven wear on brake pads or rotors
•Noise (squeaking or grinding) when braking
•Vehicle pulls to one side during braking

Diagnostic Steps

1
Inspect brake rotors for warping or uneven wear using a dial indicator.
2
Check brake pads for thickness and wear patterns.
3
Examine suspension components (control arms, tie rods, etc.) for any signs of wear or damage.
4
Test brake calipers for proper operation and piston movement.
5
Perform a visual inspection of tires for uneven wear or damage.
6
Check wheel alignment and tire balance.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Lug wrench
•Jack and jack stands
•Torque wrench
•Micrometer
•Brake cleaner
•Bungee cord

Parts Required

•Brake rotors
•Brake pads

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake rotors for warping or uneven wear using a dial indicator.
2
Check brake pads for thickness and wear patterns.
3
Examine suspension components (control arms, tie rods, etc.) for any signs of wear or damage.
4
Test brake calipers for proper operation and piston movement.
5
Perform a visual inspection of tires for uneven wear or damage.
6
Check wheel alignment and tire balance.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery for safety.

2. Remove Wheel

Use a lug wrench to loosen the lug nuts.
Raise the vehicle with a jack and secure it with jack stands.
Remove the lug nuts and take off the wheel.

3. Inspect and Replace Brake Rotors

Check the thickness of the rotors with a micrometer; replace if below minimum specifications.
If warped, remove the brake caliper (remove caliper bolts) and hang it using a bungee cord.
Remove the rotor by unscrewing the retaining screw (if present) and sliding it off the hub.
Install new rotors, ensuring they are torqued to manufacturer's specifications (usually around 80-100 ft-lbs).

4. Inspect and Replace Brake Pads

Remove the old brake pads from the caliper bracket.
Clean the caliper bracket and apply brake grease to the contact points of the new pads.
Install new brake pads, ensuring they are seated properly.

5. Reassemble Components

Reattach the brake caliper over the new pads, ensuring the caliper bolts are torqued to manufacturer specifications (typically 20-30 ft-lbs).
Reinstall the wheel and hand-tighten the lug nuts.
Lower the vehicle and torque the lug nuts to proper specifications (usually 80-100 ft-lbs).

6. Final Checks

Reconnect the battery.
Double-check all components for proper installation and function.