why does my Ford F-150 13th Generation (2015-2020) stall when I accelerate

Ford F-150 13th Generation (2015-2020)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

626 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix stalling issues during acceleration in Ford F-150 (2015-2020). Step-by-step guide with symptoms, diagnostics, and repairs.

Affected Component

Fuel System

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening any components to avoid burns.

Symptoms

•Engine stalls abruptly when accelerating
•Rough idle or hesitation before stalling
•Check engine light illuminated
•Decreased fuel efficiency
•Unusual engine noises (e.g., sputtering)
•Difficulty restarting the engine after a stall

Diagnostic Steps

1
Scan the vehicle for error codes using an OBD-II scanner.
2
Inspect the fuel system for proper pressure and flow.
3
Check the air intake system for blockages or leaks.
4
Examine the ignition system components (spark plugs, coils).
5
Test the throttle position sensor (TPS) for proper function.
6
Inspect the mass airflow sensor (MAF) for dirt or malfunction.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Fuel pressure gauge
•Socket set
•Multimeter
•Screwdrivers
•MAF cleaner

Parts Required

•Fuel filter
•Fuel pump (if necessary)
•Air filter
•Spark plugs
•Ignition coils (if necessary)
•Throttle position sensor (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle for error codes using an OBD-II scanner.
2
Inspect the fuel system for proper pressure and flow.
3
Check the air intake system for blockages or leaks.
4
Examine the ignition system components (spark plugs, coils).
5
Test the throttle position sensor (TPS) for proper function.
6
Inspect the mass airflow sensor (MAF) for dirt or malfunction.

Solution

1. Preparation

Gather tools and parts needed for repair.
Disconnect the battery to ensure safety during the repair process.
Allow the engine to cool if it has been running.

2. Inspect and Replace Fuel System Components

Fuel System Check:
- Use a fuel pressure gauge to measure fuel pressure at the rail. Ensure it meets manufacturer specifications (typically around 60-65 psi).
- If low, check the fuel filter and fuel pump for blockage or failure.
Replace Fuel Filter:
- Locate the fuel filter (usually under the vehicle near the fuel tank).
- Use a socket set to remove the filter and install a new one, ensuring all connections are secure.
Test the Fuel Pump:
- If the fuel filter is clear, check the fuel pump operation by listening for it to engage when the ignition is turned on.
- If faulty, replace the fuel pump by removing the fuel tank.

3. Inspect and Clean Air Intake Components

Air Filter Replacement:
- Open the air intake housing and remove the air filter. Replace if dirty or clogged.
Mass Airflow Sensor Cleaning:
- Disconnect the MAF sensor connector and remove the sensor from the intake.
- Use MAF cleaner to carefully clean the sensor element and reinstall.

4. Check and Replace Ignition System Parts

Inspect Spark Plugs:
- Remove spark plugs using a socket wrench. Inspect for wear or carbon buildup.
- Replace with new spark plugs if necessary, ensuring proper gap settings (typically around 0.054 inches).
Test Ignition Coils:
- Using a multimeter, check the resistance of each coil. Replace any that are out of specification.

5. Verify Throttle Position Sensor Functionality

TPS Testing:
- Use a multimeter to check the TPS for resistance changes as the throttle is opened and closed.
- Replace if the readings are inconsistent or outside of specifications.