my Ford F-150 13th Generation (2015-2020) blower motor only works on high speed what’s wrong

Ford F-150 13th Generation (2015-2020)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

509 words

Problem Statement

Learn how to diagnose and fix the blower motor issue in a 2015-2020 Ford F-150 that only works on high speed. Step-by-step guide included.

Affected Component

HVAC

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components to prevent shock or short circuits.

Symptoms

•Blower motor functions only on the highest speed setting
•Inability to adjust blower speed to lower settings (low, medium)
•Possible accompanying noise from the blower motor
•No airflow or reduced airflow at lower speed settings
•Dashboard HVAC controls responding but not affecting blower speed

Diagnostic Steps

1
Inspect the blower motor fuse for continuity using a multimeter.
2
Scan for any trouble codes related to the HVAC system using an OBD-II scanner.
3
Check the blower motor resistor for signs of damage or burning.
4
Verify the operation of the HVAC control switch by testing continuity with a multimeter.
5
Inspect wiring and connectors between the blower motor, resistor, and control module for damage.
6
Test the blower motor directly by applying battery voltage to ensure it operates properly.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Screwdriver

Parts Required

•Blower motor resistor (specific to the 2015-2020 Ford F-150)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Symptoms

•Blower motor functions only on the highest speed setting

•Inability to adjust blower speed to lower settings (low, medium)

•Possible accompanying noise from the blower motor

•No airflow or reduced airflow at lower speed settings

•Dashboard HVAC controls responding but not affecting blower speed

Diagnostic Steps

1
Inspect the blower motor fuse for continuity using a multimeter.
2
Scan for any trouble codes related to the HVAC system using an OBD-II scanner.
3
Check the blower motor resistor for signs of damage or burning.
4
Verify the operation of the HVAC control switch by testing continuity with a multimeter.
5
Inspect wiring and connectors between the blower motor, resistor, and control module for damage.
6
Test the blower motor directly by applying battery voltage to ensure it operates properly.

Solution

1. Preparation

Gather necessary tools: OBD-II scanner, multimeter, socket set, and screwdriver.
Disconnect the negative battery terminal to ensure safety during repairs.

2. Inspect and Replace Blower Motor Resistor

Remove the Glove Box:
- Open the glove box and remove any contents.
- Locate the screws or clips securing the glove box and remove them.
- Gently pull the glove box out of the way to access the blower motor resistor.
Access the Blower Motor Resistor:
- Locate the blower motor resistor, typically found near the blower motor under the dashboard.
- Disconnect the electrical connector from the resistor.
Remove the Blower Motor Resistor:
- Unscrew or unclip the resistor from its mounting position.
- Carefully take the resistor out of the housing.
Install the New Resistor:
- Position the new blower motor resistor in place.
- Secure it with screws or clips as necessary.
- Reconnect the electrical connector to the new resistor.

3. Reassemble and Test

Reinstall the Glove Box:
- Position the glove box back into place and secure it with screws or clips.
Reconnect Battery:
- Reconnect the negative battery terminal.
Test Operation:
- Start the vehicle and test the blower motor at all speed settings to ensure proper function.