my Ford F-150 13th Generation (2015-2020) AC blows warm air what’s wrong

Ford F-150 13th Generation (2015-2020)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

595 words

Problem Statement

Complete guide to fixing AC that blows warm air in Ford F-150 (2015-2020). Includes symptoms, diagnostic steps, tools required, and repair procedures.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Wear safety goggles and gloves when handling refrigerants.

Symptoms

•AC system not cooling the cabin
•Warm air coming from vents
•Increased humidity inside the vehicle
•AC compressor not engaging
•Unusual noises from the AC system
•AC system cycling on and off frequently

Diagnostic Steps

1
Check the refrigerant level using a manifold gauge set.
2
Inspect the AC compressor for proper operation and any visible damage.
3
Examine the AC condenser for blockages or damage.
4
Test the AC system pressure to confirm if it's within the normal range.
5
Inspect the electrical connections and fuses related to the AC system.
6
Scan the vehicle's OBD-II system for any related error codes.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Manifold gauge set
•Multimeter
•Vacuum pump
•Basic hand tools
•Compressed air

Parts Required

•Refrigerant
•AC compressor
•AC condenser
•Cabin air filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the refrigerant level using a manifold gauge set.
2
Inspect the AC compressor for proper operation and any visible damage.
3
Examine the AC condenser for blockages or damage.
4
Test the AC system pressure to confirm if it's within the normal range.
5
Inspect the electrical connections and fuses related to the AC system.
6
Scan the vehicle's OBD-II system for any related error codes.

Solution

1. Preparation

Gather tools: manifold gauge set, multimeter, vacuum pump, refrigerant (if needed), and basic hand tools.
Ensure the vehicle is parked on a level surface and the engine is off.

2. Check and Recharge Refrigerant

Sub-step 1: Connect the manifold gauge set to the low and high-pressure ports of the AC system.
Sub-step 2: Start the engine and turn the AC to the maximum setting.
Sub-step 3: Read the pressure gauges; if low, proceed to recharge the system.
Sub-step 4: Use a vacuum pump to evacuate the system for at least 30 minutes to remove moisture.
Sub-step 5: Recharge with the appropriate amount of refrigerant (check vehicle specifications for the correct type and amount).

3. Inspect and Replace AC Compressor (if necessary)

Sub-step 1: Disconnect the battery to ensure safety.
Sub-step 2: Remove the serpentine belt from the AC compressor.
Sub-step 3: Disconnect the electrical connector and refrigerant lines from the compressor.
Sub-step 4: Remove mounting bolts and take out the old AC compressor.
Sub-step 5: Install the new compressor and reconnect refrigerant lines and electrical connections.
Sub-step 6: Reinstall the serpentine belt.

4. Inspect Condenser and Evaporator

Sub-step 1: Locate the AC condenser and visually inspect it for debris or damage.
Sub-step 2: Clean the condenser with compressed air or water to remove any blockages.
Sub-step 3: Access the evaporator (if necessary) and inspect for leaks or blockages.

5. Electrical Inspection

Sub-step 1: Use a multimeter to check the voltage at the AC compressor connector.
Sub-step 2: Inspect and replace any blown fuses related to the AC system.
Sub-step 3: Ensure that the AC control switches are functioning correctly.