how to fix the rear view camera not working in Ford F-150 13th Generation (2015-2020)

Ford F-150 13th Generation (2015-2020)

Error Codes

1-3 hours

Time

medium

Difficulty

medium

Severity

3 min read

575 words

Problem Statement

Learn how to diagnose and fix the rear view camera not working in Ford F-150 (2015-2020). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Electrical

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to prevent short circuits.
•Allow the vehicle to cool before working around electrical components.

Symptoms

•Rear view camera display is blank or not activating
•"Camera Fault" message displayed on the dashboard
•Distorted or flickering image when the camera is activated
•No sound or alerts when the vehicle is in reverse
•Backup sensors not functioning properly

Diagnostic Steps

1
Check for any blown fuses related to the rear view camera in the fuse box.
2
Inspect the camera connection at the rear of the vehicle for any loose or damaged wires.
3
Use an OBD-II scanner to check for any error codes related to the camera system.
4
Verify the camera lens for any physical obstructions or damage.
5
Test the camera functionality using a multimeter to check for voltage at the camera connector while the vehicle is in reverse.
6
Examine the vehicle’s software for any updates that may address known issues with the camera system.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Fuse puller
•Screwdrivers
•Torque wrench

Parts Required

•Replacement fuses (if blown)
•Wiring harness (if damaged)
•Rear view camera (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check for any blown fuses related to the rear view camera in the fuse box.
2
Inspect the camera connection at the rear of the vehicle for any loose or damaged wires.
3
Use an OBD-II scanner to check for any error codes related to the camera system.
4
Verify the camera lens for any physical obstructions or damage.
5
Test the camera functionality using a multimeter to check for voltage at the camera connector while the vehicle is in reverse.
6
Examine the vehicle’s software for any updates that may address known issues with the camera system.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the ignition is turned off.
Disconnect the battery to prevent electrical shorts.

2. Inspect and Replace Fuses

Sub-steps:
- Locate the fuse box, typically found under the dashboard or in the engine compartment.
- Identify the specific fuse for the rear view camera (refer to the owner's manual).
- Use a fuse puller or pliers to remove the fuse and inspect it for continuity.
- Replace any blown fuses with the same amperage rating.

3. Check Camera Connections

Sub-steps:
- Remove the tailgate cover to access the rear view camera connector.
- Inspect the wiring harness for any signs of wear, corrosion, or disconnection.
- Reconnect any loose connectors and secure the wiring.
- If damaged, replace the wiring harness as needed.

4. Test Camera Functionality

Sub-steps:
- Reconnect the battery and turn on the ignition.
- Put the vehicle in reverse to check if the camera activates.
- If the camera still does not work, use a multimeter to measure voltage at the camera connector.
- If no voltage is present, trace the wiring back to the control module for any faults.

5. Software Update

Sub-steps:
- Visit the dealership or use a compatible OBD-II scanner to check for any software updates.
- Follow the manufacturer's instructions to install any available updates.