how to diagnose and fix rough acceleration in my Ford F-150 13th Generation (2015-2020)

Ford F-150 13th Generation (2015-2020)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

485 words

Problem Statement

Learn how to diagnose and fix rough acceleration in Ford F-150 (2015-2020). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems
•Allow engine to cool before opening any components

Symptoms

•Rough or uneven acceleration
•Engine misfires or hesitation
•Check engine light illuminated
•Decreased fuel efficiency
•Unusual engine noises during acceleration
•Vibrations felt in the cabin or steering wheel

Diagnostic Steps

1
Scan for error codes using OBD-II scanner
2
Inspect spark plugs for wear or carbon buildup
3
Check fuel system pressure using a fuel pressure gauge
4
Inspect air intake system for blockages or leaks
5
Examine ignition components for signs of damage or wear
6
Test throttle position sensor voltage output while moving the throttle

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Spark plug socket
•Torque wrench
•Fuel pressure gauge
•Multimeter
•Fuel line disconnect tool

Parts Required

•Spark plugs
•Fuel filter
•Air filter
•Throttle position sensor (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using OBD-II scanner
2
Inspect spark plugs for wear or carbon buildup
3
Check fuel system pressure using a fuel pressure gauge
4
Inspect air intake system for blockages or leaks
5
Examine ignition components for signs of damage or wear
6
Test throttle position sensor voltage output while moving the throttle

Solution

1. Preparation

Gather all necessary tools and parts.
Disconnect the negative battery terminal to ensure safety.
Ensure the engine is cool before starting repairs.

2. Replace Spark Plugs

Sub-steps:
1. Remove the ignition coil connectors.
2. Unbolt and remove the ignition coils.
3. Use a spark plug socket to remove old spark plugs.
4. Install new spark plugs, hand-tightening, then torque to 13 lb-ft (18 Nm).
5. Reinstall the ignition coils and reconnect the connectors.

3. Fuel System Repair

Sub-steps:
1. If fuel pressure is low, replace the fuel filter and inspect the fuel pump.
2. Disconnect the fuel line using a fuel line disconnect tool.
3. Replace the fuel filter by removing the retaining clips.
4. Reconnect the fuel lines and ensure there are no leaks.
5. If necessary, replace the fuel pump, following the manufacturer’s instructions.

4. Clean or Replace Air Filter

Sub-steps:
1. Open the air filter housing by unscrewing the clips or screws.
2. Remove the old air filter and inspect the housing for debris.
3. Clean the housing with a damp cloth.
4. Install a new air filter, ensuring it sits correctly in the housing.
5. Close the air filter housing securely.

5. Inspect and Replace Throttle Position Sensor (if needed)

Sub-steps:
1. Disconnect the electrical connector from the throttle position sensor.
2. Unbolt the sensor from its mounting.
3. Install the new throttle position sensor and tighten bolts to manufacturer specifications.
4. Reconnect the electrical connector.

Tools Required:

OBD-II scanner
Spark plug socket
Torque wrench
Fuel pressure gauge
Multimeter
Fuel line disconnect tool

Parts Required:

Spark plugs
Fuel filter
Air filter
Throttle position sensor (if applicable)

Estimated Repair Time: 2-4 hours

Safety Warnings:

Disconnect battery before working on electrical systems.
Allow engine to cool before opening any components.