how to fix P0750 code on Ford F-150 12th Generation (2009-2014)

Ford F-150 12th Generation (2009-2014)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0750

4 min read

657 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0750 transmission issues in Ford F-150 (2009-2014). Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0750

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the negative battery terminal to prevent electrical shorts.
•Ensure the vehicle is parked on a level surface and the engine is off.

Symptoms

•Check engine light illuminated
•Erratic shifting or inability to shift gears
•Delayed engagement when shifting from park to drive
•Transmission overheating
•Poor fuel economy
•Unusual noises from the transmission

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0750 and check for any additional codes.
2
Inspect the wiring harness and connectors for the transmission range sensor and shift solenoid A for any damage or corrosion.
3
Check the transmission fluid level and condition; low or contaminated fluid can affect transmission function.
4
Perform a continuity test on the shift solenoid A to ensure it is functioning properly.
5
Inspect the transmission range sensor for proper operation and alignment.
6
Check the transmission control module (TCM) for any faults or issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Transmission jack
•Screwdriver set
•Funnel

Parts Required

•Shift solenoid A
•Transmission range sensor
•Transmission fluid (as specified)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0750 and check for any additional codes.
2
Inspect the wiring harness and connectors for the transmission range sensor and shift solenoid A for any damage or corrosion.
3
Check the transmission fluid level and condition; low or contaminated fluid can affect transmission function.
4
Perform a continuity test on the shift solenoid A to ensure it is functioning properly.
5
Inspect the transmission range sensor for proper operation and alignment.
6
Check the transmission control module (TCM) for any faults or issues.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Inspect and Replace Wiring/Connectors

Tools Required: Socket set, wire connectors
Remove any protective coverings to access the wiring harness.
Inspect the wiring for frays or breaks and replace any damaged sections with quality wire connectors.
Ensure all connectors are securely attached and free from corrosion.

3. Check and Replace Shift Solenoid A

Tools Required: Socket set, torque wrench, transmission jack
Raise the vehicle and securely support it with jack stands.
Locate the shift solenoid A on the transmission.
Remove the electrical connector from the solenoid.
Unbolt the solenoid from the transmission, taking care to note the position of any mounting screws.
Install the new solenoid by aligning it correctly and securing it with bolts to the manufacturer's torque specifications.
Reconnect the electrical connector.

4. Inspect and Replace Transmission Range Sensor

Tools Required: Socket set, screwdriver set
Locate the transmission range sensor on the transmission.
Disconnect the electrical connector and unbolt the sensor.
Carefully remove the sensor, taking note of the alignment.
Install the new sensor, ensuring it is aligned correctly, and reattach the mounting bolts.
Reconnect the electrical connector.

5. Refill Transmission Fluid

Tools Required: Funnel, transmission fluid (as specified in the owner's manual)
Check the fluid level through the dipstick tube and add fluid as necessary, ensuring it meets the manufacturer's specifications.
Start the engine and let it run for a few minutes, then check the fluid level again, topping off if needed.

6. Reconnect Battery and Test Drive

Reconnect the negative battery terminal.
Start the vehicle and allow it to reach operating temperature.
Test drive the vehicle to ensure proper shifting and that the Check Engine light does not illuminate again.