how to fix P0700 code on Ford F-150 12th Generation (2009-2014)

Ford F-150 12th Generation (2009-2014)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700

3 min read

501 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0700 transmission control system malfunction in Ford F-150 (2009-2014). Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0700

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before inspecting or adding fluid to the transmission.

Symptoms

•Check engine light illuminated
•Rough shifting or delayed engagement
•Transmission overheating
•Unresponsive transmission (stuck in gear or fails to shift)
•Poor acceleration or loss of power

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for related codes.
2
Inspect transmission fluid level and condition (check for contamination or burnt smell).
3
Check for any visible leaks around the transmission and its connectors.
4
Inspect the wiring and connectors to the transmission control module (TCM) for damage or corrosion.
5
Test the TCM for proper function using a multimeter.
6
Check the vehicle's battery voltage and charging system to ensure proper electrical supply.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Funnel
•Wire cutter/stripper
•Electrical tape or heat-shrink tubing

Parts Required

•Transmission fluid (specific to Ford specifications)
•Transmission Control Module (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for related codes.
2
Inspect transmission fluid level and condition (check for contamination or burnt smell).
3
Check for any visible leaks around the transmission and its connectors.
4
Inspect the wiring and connectors to the transmission control module (TCM) for damage or corrosion.
5
Test the TCM for proper function using a multimeter.
6
Check the vehicle's battery voltage and charging system to ensure proper electrical supply.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Check and Change Transmission Fluid

Sub-steps:
1. Locate the transmission dipstick and remove it.
2. Using a funnel, add the appropriate transmission fluid (consult the owner’s manual for the specific type).
3. Start the engine and let it idle; shift through all gears slowly.
4. Recheck the fluid level and add more if necessary.
Tools Required:
- Funnel
- Transmission fluid (specific to Ford specifications)

3. Inspect and Repair Wiring

Sub-steps:
1. Locate the wiring harness connected to the TCM and transmission.
2. Inspect for any signs of wear, fraying, or corrosion.
3. Repair or replace damaged wiring as needed.
4. Ensure all connections are secure.
Tools Required:
- Wire cutter/stripper
- Electrical tape or heat-shrink tubing
- Multimeter (for testing continuity)

4. Replace Transmission Control Module (if necessary)

Sub-steps:
1. Locate the TCM (usually found near the transmission).
2. Disconnect the wiring harness from the TCM.
3. Remove the TCM mounting bolts using a socket set.
4. Install the new TCM and secure it with mounting bolts.
5. Reconnect the wiring harness.
Tools Required:
- Socket set
- Replacement TCM