why does my Ford Explorer Sixth Generation (2020-present) have a loss of power when driving

Ford Explorer Sixth Generation (2020-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

602 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix loss of power issues in the 2020 Ford Explorer. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool completely before performing maintenance.

Symptoms

•Check engine light illuminated
•Noticeable decrease in acceleration
•Engine stalling or misfiring
•Poor fuel economy
•Unusual engine noises (e.g., knocking or pinging)
•Increased exhaust emissions

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify potential issues.
2
Inspect the air filter for blockages and replace if necessary.
3
Check fuel pressure with a fuel pressure gauge to ensure proper fuel delivery.
4
Examine the throttle body for carbon buildup or obstructions.
5
Test the ignition system components (spark plugs, ignition coils) for faults.
6
Inspect vacuum lines for leaks that could affect engine performance.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Fuel pressure gauge
•Socket set
•Throttle body cleaner
•Soft brush
•Multimeter

Parts Required

•Air filter
•Fuel filter (if needed)
•Spark plugs (if worn)
•Ignition coils (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify potential issues.
2
Inspect the air filter for blockages and replace if necessary.
3
Check fuel pressure with a fuel pressure gauge to ensure proper fuel delivery.
4
Examine the throttle body for carbon buildup or obstructions.
5
Test the ignition system components (spark plugs, ignition coils) for faults.
6
Inspect vacuum lines for leaks that could affect engine performance.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the engine is cool and vehicle is in a safe working environment.
Disconnect the battery to prevent electrical shorts.

2. Air Filter Replacement

Sub-steps:
1. Locate the air filter housing; usually found near the front of the engine compartment.
2. Remove the screws or clips securing the air filter housing cover.
3. Take out the old air filter and inspect the housing for debris.
4. Install the new air filter, ensuring it fits snugly.
5. Reattach the housing cover and secure it with screws or clips.

3. Fuel Pressure Check

Tools Required: Fuel pressure gauge
Sub-steps:
1. Locate the fuel rail on the engine.
2. Connect the fuel pressure gauge to the test port on the fuel rail.
3. Turn the ignition to the "ON" position without starting the engine to check the pressure reading.
4. Compare the reading to the manufacturer's specifications (typically between 50-60 PSI).
5. If the pressure is low, check the fuel pump and fuel filter for issues.

4. Throttle Body Cleaning

Tools Required: Throttle body cleaner, soft brush
Sub-steps:
1. Locate the throttle body; it is usually connected to the intake manifold.
2. Remove the intake duct connected to the throttle body.
3. Spray throttle body cleaner inside the throttle body while opening the throttle plate manually.
4. Use a soft brush to remove any carbon buildup.
5. Reconnect the intake duct securely.

5. Ignition System Inspection

Sub-steps:
1. Remove the ignition coils by unscrewing the retaining bolts.
2. Pull out the spark plugs using a spark plug socket.
3. Inspect the spark plugs for wear or carbon deposits and replace if necessary.
4. Test ignition coils with a multimeter for proper resistance.
5. Reinstall the coils and spark plugs securely.