what maintenance should I do at 60,000 miles on my Ford Explorer Sixth Generation (2020-present)

Ford Explorer Sixth Generation (2020-present)

Error Codes

3-5 hours

Time

medium

Difficulty

medium

Severity

3 min read

584 words

Problem Statement

Learn essential maintenance steps for your 2020-present Ford Explorer at 60,000 miles. Ensure optimal performance with our comprehensive guide.

Affected Component

Engine

Estimated Time

3-5 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always allow the engine to cool before starting maintenance.
•Use jack stands when working under the vehicle to prevent accidents.

Symptoms

•Decreased fuel efficiency
•Unusual noises from the engine or suspension
•Warning lights illuminated on the dashboard
•Vibration during driving
•Difficulty in steering or handling

Diagnostic Steps

1
Review the owner's manual for specific 60,000-mile service recommendations.
2
Inspect and replace the engine oil and oil filter.
3
Check and replace the air filter, cabin air filter, and fuel filter if necessary.
4
Inspect the brake system, including pads, rotors, and fluid levels.
5
Check tire conditions, including tread depth and inflation pressure; rotate tires if needed.
6
Inspect the suspension system and steering components for wear.
7
Perform a visual inspection of belts and hoses for signs of wear or cracking.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Oil filter wrench
•Tire pressure gauge
•Lug wrench
•Brake fluid tester

Parts Required

•Engine oil (synthetic)
•Oil filter
•Air filter
•Cabin air filter
•Brake pads and rotors (if required)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Review the owner's manual for specific 60,000-mile service recommendations.
2
Inspect and replace the engine oil and oil filter.
3
Check and replace the air filter, cabin air filter, and fuel filter if necessary.
4
Inspect the brake system, including pads, rotors, and fluid levels.
5
Check tire conditions, including tread depth and inflation pressure; rotate tires if needed.
6
Inspect the suspension system and steering components for wear.
7
Perform a visual inspection of belts and hoses for signs of wear or cracking.

Solution

1. Oil Change

Drain the old engine oil using a wrench to remove the oil drain plug.
Replace the oil filter using an oil filter wrench.
Reinstall the oil drain plug and tighten to manufacturer specifications (typically 20-25 ft-lbs).
Fill the engine with fresh oil as per specifications (usually 6-7 quarts of synthetic oil).

2. Air and Cabin Filter Replacement

Open the hood and locate the air filter housing; remove the clips and cover.
Replace the old air filter with a new one, ensuring it fits snugly.
For the cabin air filter, access the filter compartment (usually behind the glove box) and replace it as per instructions.

3. Brake Inspection and Service

Remove the wheel to access the brake caliper and rotor.
Inspect brake pads for wear; replace if thickness is below 3 mm.
Check the brake fluid level and quality; flush and replace if it appears dirty or contaminated.

4. Tire Rotation and Inspection

Remove all four tires using a lug wrench.
Inspect tire tread depth with a gauge; replace tires if below 2/32 inches.
Rotate tires to ensure even wear (front to back, and back to front).
Reinstall wheels and torque lug nuts to manufacturer specifications (usually 100-110 ft-lbs).

5. Suspension and Steering Inspection

Visually inspect shocks/struts for fluid leaks or damage.
Check ball joints and tie rod ends for play; replace if any movement is detected.
Ensure all steering components are tight and undamaged.

6. Belts and Hoses Inspection

Inspect serpentine belts for cracks or fraying; replace if necessary.
Check hoses for leaks, bulges, or softness; replace any damaged hoses.