how do I fix the rear air conditioning not blowing cold in my Ford Explorer Sixth Generation (2020-p...

Ford Explorer Sixth Generation (2020-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

587 words

Problem Statement

Learn how to diagnose and fix rear A/C not blowing cold in Ford Explorer (2020-present). Step-by-step guide with tools and procedures included.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Wear safety goggles and gloves when handling refrigerants.

Symptoms

•Rear A/C is blowing warm air
•Unusual noises from the rear A/C unit
•A/C system operates intermittently
•Increased humidity inside the vehicle
•Front A/C functioning normally

Diagnostic Steps

1
Check the refrigerant level in the A/C system using a manifold gauge set.
2
Inspect the rear A/C blower motor for proper operation.
3
Scan for any error codes related to the A/C system using an OBD-II scanner.
4
Verify the operation of the A/C compressor by observing its engagement.
5
Inspect the A/C lines for leaks or visible damage.
6
Check the cabin air filter for clogs or restrictions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Manifold gauge set
•OBD-II scanner
•Multimeter
•Socket set
•Screwdriver

Parts Required

•Refrigerant
•Blower motor (if needed)
•Cabin air filter (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the refrigerant level in the A/C system using a manifold gauge set.
2
Inspect the rear A/C blower motor for proper operation.
3
Scan for any error codes related to the A/C system using an OBD-II scanner.
4
Verify the operation of the A/C compressor by observing its engagement.
5
Inspect the A/C lines for leaks or visible damage.
6
Check the cabin air filter for clogs or restrictions.

Solution

1. Preparation

Gather tools and parts needed for repair.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Recharge Refrigerant

Tools Required: Manifold gauge set, refrigerant.
Locate the low-pressure service port on the A/C system.
Connect the low side hose of the manifold gauge to the service port.
Start the engine and turn on the A/C to the maximum setting.
Add refrigerant as needed until the pressure readings are within the manufacturer's specifications (typically around 30-40 PSI).
Disconnect the manifold gauge and replace the service port cap.

3. Inspect and Replace Blower Motor (if necessary)

Tools Required: Socket set, screwdriver.
Remove the access panel for the rear A/C unit, usually located under the dashboard or in the rear cargo area.
Disconnect the electrical connector from the blower motor.
Remove the mounting screws and take out the blower motor.
Inspect for damage or debris; replace if necessary with a new unit.
Reinstall the blower motor and reconnect the electrical connector.

4. Check A/C Compressor

Tools Required: Multimeter.
Locate the A/C compressor and inspect the electrical connections.
Use a multimeter to check the voltage at the compressor when the A/C is on.
If there is no voltage, trace the wiring for shorts or faults.
If the compressor does not engage, consider replacement if it is faulty.

5. Clear Drainage and Check Cabin Air Filter

Tools Required: Screwdriver.
Locate the cabin air filter, typically behind the glove box or under the dashboard.
Remove the old filter and inspect it for dirt or clogs; replace it if necessary.
Check the drainage tube for the A/C condensation and clear any blockage that may prevent proper drainage.