how to fix the warning light for low tire pressure in my Ford Explorer Fifth Generation (2011-2019)

Ford Explorer Fifth Generation (2011-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

547 words

Problem Statement

Learn how to fix the low tire pressure warning light on your Ford Explorer (2011-2019). Step-by-step guide with diagnostic steps and repair instructions.

Affected Component

Suspension

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is on a stable surface and securely supported when working on tires.
•Be cautious when handling tire inflators to avoid over-inflation.

Symptoms

•Low tire pressure warning light illuminated on the dashboard
•Possible decrease in ride comfort or handling
•Uneven tire wear visible upon inspection
•Tire pressure readings below recommended levels

Diagnostic Steps

1
Check the tire pressure of all four tires using a tire pressure gauge.
2
Inspect each tire visually for signs of damage, punctures, or air leaks.
3
Verify the TPMS functionality by using an OBD-II scanner to check for stored error codes.
4
Reset the TPMS system according to the manufacturer's instructions.
5
Check the condition and battery status of the TPMS sensors if equipped.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Tire pressure gauge
•OBD-II scanner
•Tire inflator

Parts Required

•TPMS sensors (if replacement is necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the tire pressure of all four tires using a tire pressure gauge.
2
Inspect each tire visually for signs of damage, punctures, or air leaks.
3
Verify the TPMS functionality by using an OBD-II scanner to check for stored error codes.
4
Reset the TPMS system according to the manufacturer's instructions.
5
Check the condition and battery status of the TPMS sensors if equipped.

Solution

1. Preparation

Gather the necessary tools and materials.
Ensure the vehicle is parked on a level surface and the engine is off.
Tools Required: Tire pressure gauge, OBD-II scanner, tire inflator.

2. Check and Inflate Tires

Sub-step 1: Remove valve caps from each tire.
Sub-step 2: Use the tire pressure gauge to measure the current pressure in each tire.
Sub-step 3: Compare the readings to the recommended tire pressures (usually found on the driver's side door jamb).
Sub-step 4: If any tire is below the recommended pressure, use a tire inflator to add air until it reaches the appropriate level.
Sub-step 5: Replace the valve caps securely after checking/inflating.

3. Inspect and Replace TPMS Sensors (if necessary)

Sub-step 1: If the tire pressure is correct and the warning light remains, get access to the wheel assembly by removing the tire if needed.
Sub-step 2: Locate the TPMS sensor on the inside of the tire.
Sub-step 3: Inspect the sensor for damage; if damaged, remove the old sensor and replace it with a new one.
Sub-step 4: Reinstall the tire and ensure it is properly balanced.

4. Reset the TPMS

Sub-step 1: Turn the ignition key to the "ON" position without starting the engine.
Sub-step 2: Press the TPMS reset button (usually located under the steering column or in the glove box).
Sub-step 3: Hold the button until the TPMS warning light blinks three times and then turns off.
Sub-step 4: Start the engine and confirm the warning light is no longer illuminated.