my BMW X5 G05 (2019-2024) remote start isn’t working, what can I do?

BMW X5 G05 (2019-2024)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

547 words

Problem Statement

The remote start feature of a BMW X5 G05 (2019-2024) is non-functional, preventing the vehicle from starting remotely.

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems to avoid shorts or shocks.

Symptoms

•Remote start feature does not activate
•Key fob not responding or showing low battery
•No sound or indication of the engine starting
•Check engine light illuminated (if related)
•Door locks not responding to remote commands

Diagnostic Steps

1
Verify the key fob battery is charged and replace it if necessary.
2
Check for any error codes using an OBD-II scanner that might indicate issues with the remote start system.
3
Inspect the vehicle's battery voltage to ensure it is sufficient for the remote start function.
4
Confirm that the vehicle is in an appropriate condition for remote start (e.g., doors closed, hood closed, and vehicle not in gear).
5
Check the settings in the vehicle's infotainment system to ensure remote start is enabled.
6
Inspect the antenna and wiring for the remote start system for any visible damage or disconnection.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Ensure the vehicle is parked in a safe location.
•Disconnect the battery negative terminal for safety.

Parts Required

•CR2032 battery (for key fob)
•Vehicle battery (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Verify the key fob battery is charged and replace it if necessary.
2
Check for any error codes using an OBD-II scanner that might indicate issues with the remote start system.
3
Inspect the vehicle's battery voltage to ensure it is sufficient for the remote start function.
4
Confirm that the vehicle is in an appropriate condition for remote start (e.g., doors closed, hood closed, and vehicle not in gear).
5
Check the settings in the vehicle's infotainment system to ensure remote start is enabled.
6
Inspect the antenna and wiring for the remote start system for any visible damage or disconnection.

Solution

1. Preparation

Tools Required: OBD-II scanner, multimeter, flathead screwdriver, T20 Torx screwdriver.
Ensure the vehicle is parked in a safe location.
Disconnect the battery negative terminal for safety.

2. Replace Key Fob Battery

Use a flathead screwdriver to carefully pry open the key fob.
Remove the old battery and replace it with a new CR2032 battery, ensuring correct polarity (+/-).
Reassemble the key fob and test the remote start function.

3. Check Vehicle Battery Voltage

Use a multimeter to measure the voltage of the vehicle's battery.
If the voltage is below 12.4 volts, charge the battery or replace it if necessary.

4. Inspect Remote Start System Settings

Reconnect the battery terminal.
Start the vehicle using the ignition key.
Access the vehicle's infotainment system settings and navigate to 'Remote Start Settings'.
Ensure the remote start feature is enabled and save any changes.

5. Inspect Antenna and Wiring

Remove any covers or panels to access the remote start receiver antenna.
Visually inspect the antenna and wiring for damage or loose connections.
Reconnect any loose wires and replace any damaged components.

6. Test the Remote Start Function

After completing the above steps, test the remote start function using the key fob.
Ensure that the vehicle meets the conditions for remote start (doors locked, hood closed, etc.).