FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
why does my BMW 5 Series G30/G31 (2017-2024) engine light flash when accelerating - BMW 5 Series
Home/Cars/BMW/5 Series/G30/G31 (2017-2024)/why does my BMW 5 Series G30/G31 (2017-2024) engine light flash when accelerating

why does my BMW 5 Series G30/G31 (2017-2024) engine light flash when accelerating

BMW 5 Series G30/G31 (2017-2024)

Error Codes
2-4 hours
Time
medium
Difficulty
medium
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
3 min read
583 words

Problem Statement

The engine light on a 2017-2024 BMW 5 Series G30/G31 is flashing during acceleration, indicating a potential issue with the engine or drivetrain that needs immediate attention.

Estimated Time
2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

  • •Disconnect the battery before working on electrical systems.
  • •Allow the engine to cool before performing any maintenance.

Symptoms

  • •Flashing check engine light
  • •Rough acceleration
  • •Decreased engine performance
  • •Engine misfires
  • •Unusual engine noises (e.g., knocking or popping)
  • •Increased fuel consumption

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •OBD-II scanner
  • •Socket set
  • •Multimeter
  • •Fuel pressure gauge
  • •Screwdriver set

Parts Required

  • •Spark plugs
  • •Ignition coils (if faulty)
  • •Fuel filter (if necessary)
  • •Air filter (if necessary)

Additional Information

Estimated Time
2-4 hours
Difficulty
medium
Severity
medium
Tools Required
5 items
Parts Required
4 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation
Solution
1. Preparation
  • Gather necessary tools and parts.
  • Ensure the vehicle is parked on a flat surface and the engine is cool.
2. Scan for Error Codes
  • Connect the OBD-II scanner to the vehicle's diagnostic port.
  • Turn on the ignition without starting the engine and retrieve fault codes.
  • Document any codes present for reference during repair.
3. Inspect and Replace Ignition Components
  • Remove engine cover (if applicable).
  • Use a socket set to remove spark plugs; inspect for wear or damage.
  • Test ignition coils using a multimeter; replace any faulty coils.
  • Reinstall new spark plugs according to manufacturer specifications, torquing to 25 Nm (18 lb-ft).
4. Check and Adjust Fuel Pressure
  • Connect a fuel pressure gauge to the fuel rail.
  • Start the engine and monitor fuel pressure; compare with manufacturer specifications (usually around 50-60 PSI).
  • If pressure is low, check the fuel filter and pump for blockages or failures; replace as needed.
5. Inspect Air Intake and MAF Sensor
  • Remove the air intake duct to access the MAF sensor.
  • Clean the MAF sensor with MAF cleaner to remove dirt and debris.
  • Inspect the air filter; replace if dirty or clogged.
6. Examine Exhaust System
  • Visually inspect the exhaust system for leaks or damage, especially around the catalytic converter.
  • If any restrictions are found, replace damaged components.
7. Test Engine Vacuum
  • Use a vacuum gauge to check for engine vacuum.
  • A normal reading is typically 18-22 inHg; any significant deviation suggests a vacuum leak.
  • Repair any vacuum leaks found in hoses or gaskets.