FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
my BMW 5 Series F10/F11 (2010-2017) has poor acceleration, what's wrong - BMW 5 Series
Home/Cars/BMW/5 Series/F10/F11 (2010-2017)/my BMW 5 Series F10/F11 (2010-2017) has poor acceleration, what's wrong

my BMW 5 Series F10/F11 (2010-2017) has poor acceleration, what's wrong

BMW 5 Series F10/F11 (2010-2017)

Error Codes
2-4 hours
Time
medium
Difficulty
medium
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
3 min read
588 words

Problem Statement

The BMW 5 Series F10/F11 (2010-2017) is experiencing poor acceleration, indicating a potential issue with the engine performance or related systems.

Estimated Time
2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

  • •Disconnect battery before working on electrical systems.
  • •Allow the engine to cool before removing components.

Symptoms

  • •Check engine light illuminated
  • •Reduced engine power
  • •Rough acceleration or hesitation during acceleration
  • •Increased fuel consumption
  • •Unusual engine noises (e.g., knocking or pinging)
  • •Smoke from the exhaust

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •Remove the air filter cover.
  • •Take out the air filter and inspect it for dirt and clogs.
  • •Replace with a new air filter if necessary.

Parts Required

  • •Air filter
  • •Fuel pump (if necessary)
  • •Throttle position sensor (if necessary)
  • •Spark plugs

Additional Information

Estimated Time
2-4 hours
Difficulty
medium
Severity
medium
Tools Required
3 items
Parts Required
4 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation
Solution
1. Preparation
  • Gather all necessary tools and parts.
  • Disconnect the battery to ensure safety while working on electrical components.
  • Ensure the vehicle is on a flat surface and secure it with wheel chocks.
2. Address Air Filter
  • Tools Required: Screwdriver or socket set
  • Remove the air filter cover.
  • Take out the air filter and inspect it for dirt and clogs.
  • Replace with a new air filter if necessary.
3. Inspect Fuel System
  • Tools Required: Fuel pressure gauge
  • Locate the fuel pressure test port on the fuel rail.
  • Connect the fuel pressure gauge and turn the ignition to the "ON" position without starting the engine.
  • Check the fuel pressure reading against specifications (typically around 50-60 psi for most BMW models).
  • If pressure is low, check the fuel pump and replace it if faulty.
4. Test Throttle Position Sensor (TPS)
  • Tools Required: Multimeter
  • Locate the TPS on the throttle body.
  • Disconnect the electrical connector and set the multimeter to voltage mode.
  • Measure the voltage output while slowly opening the throttle. It should change smoothly from 0.5V to approximately 4.5V.
  • If the output is erratic or outside the specified range, replace the TPS.
5. Examine Spark Plugs
  • Tools Required: Spark plug socket and ratchet
  • Remove the spark plug wires and then the spark plugs.
  • Inspect the electrodes for wear or carbon buildup.
  • Replace any worn or fouled spark plugs with the manufacturer-recommended type.
6. Check for Vacuum Leaks
  • Tools Required: Smoke machine or carburetor cleaner
  • Visually inspect all vacuum hoses for cracks or disconnections.
  • Use a smoke machine to introduce smoke into the intake system to detect leaks.
  • Repair or replace any damaged hoses found during inspection.