why is my Volkswagen Golf MK7.5 (2020-Present) making a clicking noise when I turn the key?

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

1-3 hours

Time

medium

Difficulty

high

Severity

3 min read

458 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the clicking noise when turning the key in Volkswagen Golf MK7.5. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to prevent shocks or shorts.

Symptoms

•Clicking noise when the ignition key is turned
•Engine does not crank or start
•Dashboard lights may dim or flicker
•Possible battery warning light illuminated
•Electrical accessories may function intermittently

Diagnostic Steps

1
Inspect the battery terminals for corrosion or loose connections.
2
Use a multimeter to check the battery voltage (should be around 12.6 volts or higher).
3
Test the battery under load to ensure it can hold voltage when starting.
4
Check the fuses related to the starting system for any blown fuses.
5
Inspect the starter motor connections and wiring for any damage or looseness.
6
Scan the vehicle’s OBD-II system for any error codes related to the starting system.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Wrench set

Parts Required

•New battery (if required)
•New starter motor (if required)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the battery terminals for corrosion or loose connections.
2
Use a multimeter to check the battery voltage (should be around 12.6 volts or higher).
3
Test the battery under load to ensure it can hold voltage when starting.
4
Check the fuses related to the starting system for any blown fuses.
5
Inspect the starter motor connections and wiring for any damage or looseness.
6
Scan the vehicle’s OBD-II system for any error codes related to the starting system.

Solution

1. Preparation

Tools Required: OBD-II scanner, multimeter, socket set, and wrench set.
Disconnect the negative terminal of the battery to ensure safety while working on electrical components.

2. Battery Inspection

Sub-steps:
1. Inspect the battery terminals for any corrosion or loose connections; clean and tighten if necessary.
2. If the battery is weak or below 12.4 volts, proceed to replace it.

3. Starter Motor Inspection

Sub-steps:
1. Locate the starter motor (usually near the engine block).
2. Check the wiring and connections to the starter for damage or looseness.
3. If connections are secure and undamaged, use a multimeter to test the starter motor's voltage when the key is turned to the start position.

4. Replace Faulty Components

Sub-steps:
1. If the battery is confirmed defective, replace it with a new one (ensure the new battery matches specifications).
2. If the starter motor is faulty, remove it by disconnecting the electrical connections and unscrewing the mounting bolts; replace it with a new starter motor.

5. Reconnect Battery and Test

Reconnect the negative battery terminal.
Attempt to start the vehicle to verify that the issue has been resolved.