how to replace the struts on my Volkswagen Golf MK7.5 (2020-Present)?

Volkswagen Golf MK7.5 (2020-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

576 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Step-by-step guide on how to replace struts on your Volkswagen Golf MK7.5 (2020-Present). Diagnose symptoms, gather tools, and follow the repair process.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when the vehicle is lifted.
•Use a strut spring compressor to avoid injury when handling compressed springs.

Symptoms

•Excessive bouncing or swaying during driving
•Noise from the strut area over bumps
•Uneven tire wear
•Vehicle feels unstable or has poor handling
•Fluid leakage around the strut assembly

Diagnostic Steps

1
Inspect the struts visually for signs of fluid leakage and physical damage.
2
Check the vehicle's alignment to confirm if misalignment is contributing to uneven tire wear.
3
Perform a bounce test by pushing down on the front or rear of the vehicle to assess strut responsiveness.
4
Use an OBD-II scanner to check for any related error codes that may indicate suspension issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Socket set
•Torque wrench
•Strut spring compressor
•Impact wrench (optional)

Parts Required

•New struts (front and/or rear as necessary)
•New strut mounts (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the struts visually for signs of fluid leakage and physical damage.
2
Check the vehicle's alignment to confirm if misalignment is contributing to uneven tire wear.
3
Perform a bounce test by pushing down on the front or rear of the vehicle to assess strut responsiveness.
4
Use an OBD-II scanner to check for any related error codes that may indicate suspension issues.

Solution

1. Preparation

Tools Required: Jack, jack stands, socket set, torque wrench, strut spring compressor, impact wrench (optional).
Lift the vehicle using a jack and secure it with jack stands.
Remove the wheel to access the strut assembly.

2. Remove the Strut Assembly

Disconnect the Stabilizer Bar Link:
- Use a wrench to hold the stabilizer bar link and remove the nut with a socket.
Remove the Lower Strut Bolts:
- Remove the bolts securing the strut to the lower control arm using a socket.
- Use an impact wrench if necessary to loosen stubborn bolts.
Remove the Upper Strut Mount:
- Open the hood and locate the upper strut mount.
- Remove the nuts securing the strut mount to the chassis using a socket and ratchet.
Extract the Strut Assembly:
- Carefully pull the strut assembly out from the wheel well and lower control arm.

3. Install New Struts

Prepare New Strut:
- If the new struts require installation of the spring, use a strut spring compressor to safely compress the spring and remove the old strut from the spring.
Reassemble:
- Install the new strut into the spring (if applicable) and secure with the strut mount nuts. Ensure the spring is seated properly.
- Reinsert the strut assembly into the vehicle, aligning it with the upper mount and lower control arm.
Secure Strut Assembly:
- Tighten the upper strut mount nuts to the manufacturer’s specified torque.
- Reattach the lower strut bolts and tighten them to the specified torque.
Reconnect Stabilizer Bar Link:
- Reattach the stabilizer bar link and secure with the nut.

4. Reassemble the Vehicle

Reinstall the wheel and lower the vehicle from the jack stands.
Torque the lug nuts to the specified value.