my Volkswagen Golf MK7 (2015-2019) makes a shuddering noise when accelerating what's wrong

Volkswagen Golf MK7 (2015-2019)

Error Codes

3-5 hours

Time

medium

Difficulty

medium

Severity

3 min read

575 words

Problem Statement

Learn how to diagnose and fix shuddering noise during acceleration in Volkswagen Golf MK7 (2015-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

3-5 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening any components.

Symptoms

•Shuddering noise when accelerating
•Loss of power during acceleration
•Vibrations felt through the steering wheel and/or floorboard
•Possible check engine light illuminated
•Engine misfire or hesitation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the transmission fluid level and condition; check for contamination.
3
Check engine mounts for wear or damage that could lead to excessive movement.
4
Examine the drive shafts and CV joints for signs of wear or damage.
5
Test the ignition system components, including spark plugs and coils, for proper operation.
6
Look for any vacuum leaks in the intake system that could affect engine performance.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Fluid pump
•Jack and jack stands

Parts Required

•Engine mounts
•Transmission fluid
•Spark plugs
•Drive shaft/CV joint (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the transmission fluid level and condition; check for contamination.
3
Check engine mounts for wear or damage that could lead to excessive movement.
4
Examine the drive shafts and CV joints for signs of wear or damage.
5
Test the ignition system components, including spark plugs and coils, for proper operation.
6
Look for any vacuum leaks in the intake system that could affect engine performance.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the battery to ensure safety while working on electrical components.
Ensure the vehicle is on a flat surface and secure it with wheel chocks.

2. Inspect and Replace Engine Mounts

Sub-steps:
- Remove any covers obstructing access to the engine mounts.
- Use a jack to support the engine slightly while you replace the mounts.
- Remove the bolts securing the damaged engine mount using a socket set.
- Install the new engine mount, ensuring it is properly aligned.
- Torque bolts to the manufacturer's specifications (typically around 30-50 Nm).

3. Check and Replace Transmission Fluid

Sub-steps:
- Locate the transmission drain and fill plugs.
- Using a fluid pump, remove old transmission fluid.
- Inspect the fluid for metal shavings or burnt smell, indicating internal damage.
- Replace with the recommended transmission fluid (consult the owner's manual for type).
- Reinstall the fill plug, ensuring it is secure.

4. Inspect and Replace Spark Plugs

Sub-steps:
- Remove the ignition coils/cover to access the spark plugs.
- Use a spark plug socket to remove each spark plug.
- Inspect for wear, fouling, or damage; replace as necessary.
- Install new spark plugs, tightening to the manufacturer’s torque specification (typically 20-30 Nm).

5. Inspect Drive Shafts and CV Joints

Sub-steps:
- Lift the vehicle and secure with jack stands.
- Visually inspect the drive shafts and CV joints for tears in the rubber boots and signs of grease leakage.
- If damaged, remove the affected drive shaft by unbolting it from the transmission and hub.
- Install new components, ensuring all bolts are torqued to specifications.