my Volkswagen Golf MK7 (2015-2019) makes a clicking noise when turning what's wrong

Volkswagen Golf MK7 (2015-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

565 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Volkswagen Golf MK7 (2015-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical components.
•Allow the vehicle to cool before working on hot components like brakes.

Symptoms

•Clicking noise during left or right turns
•Noise increases with sharper turns
•Possible vibrations in the steering wheel
•Unusual wear on tires
•No loss of steering control

Diagnostic Steps

1
Inspect the front axles for damage or wear.
2
Check the CV joints for torn boots or corrosion.
3
Examine the wheel bearings for play or noise.
4
Look for loose or damaged suspension components (e.g., control arms, tie rods).
5
Test drive the vehicle to replicate the noise while observing the steering response.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Socket set
•Torque wrench
•Pry bar
•Bearing puller

Parts Required

•CV joint assembly (if damaged)
•Wheel bearing (if damaged)
•Suspension components (if found faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front axles for damage or wear.
2
Check the CV joints for torn boots or corrosion.
3
Examine the wheel bearings for play or noise.
4
Look for loose or damaged suspension components (e.g., control arms, tie rods).
5
Test drive the vehicle to replicate the noise while observing the steering response.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the battery for safety.
Tools required: Jack, jack stands, socket set, torque wrench, pry bar.

2. Inspect and Replace CV Joints

Inspect CV Joints:
1. Lift the front of the vehicle using a jack and secure it with jack stands.
2. Remove the front wheels using a socket set.
3. Inspect the CV joint boots for tears or grease leakage.
4. If the boot is damaged, replace the CV joint assembly.
Replace CV Joint (if necessary):
1. Remove the retaining clips and bolts securing the CV joint to the axle.
2. Use a pry bar to detach the CV joint from the wheel hub.
3. Install the new CV joint by reversing the removal process, ensuring proper alignment and torque specifications (typically 30-40 Nm for retaining bolts).

3. Inspect and Replace Wheel Bearings

Inspect Wheel Bearings:
1. Spin the wheel hub to feel for roughness or noise.
2. Remove the dust cap and check for any play in the bearing.
Replace Wheel Bearing (if necessary):
1. Remove the brake caliper and rotor for access.
2. Use a bearing puller to remove the old bearing from the hub.
3. Press in the new bearing, ensuring it is seated correctly.
4. Reinstall the rotor and caliper, torquing bolts to manufacturer specifications.

4. Inspect Suspension Components

Check Suspension:
1. Visually inspect control arms, tie rods, and sway bar links for damage or wear.
2. Use a pry bar to check for excessive play in the components.
Replace Any Damaged Parts:
1. Remove any damaged components using the appropriate sockets.
2. Install new parts, ensuring proper torque specifications are followed.