how to fix SRS light on Toyota Highlander XU70 (2020-Present)

Toyota Highlander XU70 (2020-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

critical

Severity

3 min read

495 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the SRS light issue in Toyota Highlander XU70 (2020-Present). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on airbag systems to prevent accidental deployment.
•Allow the vehicle to sit for at least 10 minutes after disconnecting the battery before accessing SRS components.

Symptoms

•SRS warning light illuminated on the dashboard
•Possible malfunction of airbags during an accident
•Seat belt pretensioners not functioning correctly
•Diagnostic trouble codes (DTCs) present related to SRS
•Increased risk of airbag deployment failure

Diagnostic Steps

1
Use an OBD-II scanner to check for any related error codes in the SRS system.
2
Inspect the airbag system wiring harness for any visible damage or disconnections.
3
Check the status of the seat belt buckle sensors and connections.
4
Verify the integrity of the airbag modules in the steering wheel and passenger dashboard.
5
Inspect the vehicle’s battery and fuse related to the SRS system for any issues.
6
Reset the SRS light using the OBD-II scanner and check if it re-illuminates after a vehicle restart.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Screwdriver
•Wire stripper
•Soldering iron

Parts Required

•Seat belt buckle sensor
•Wiring harness

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Use an OBD-II scanner to check for any related error codes in the SRS system.
2
Inspect the airbag system wiring harness for any visible damage or disconnections.
3
Check the status of the seat belt buckle sensors and connections.
4
Verify the integrity of the airbag modules in the steering wheel and passenger dashboard.
5
Inspect the vehicle’s battery and fuse related to the SRS system for any issues.
6
Reset the SRS light using the OBD-II scanner and check if it re-illuminates after a vehicle restart.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the ignition is turned off.
Disconnect the negative battery terminal to prevent accidental airbag deployment.

2. Inspect and Repair Wiring

Tools Required: Multimeter, wire stripper, soldering iron (if needed)
Check the wiring harness for continuity using a multimeter.
Repair any damaged wires by stripping, soldering, and insulating them properly.
Reconnect any loose connections securely.

3. Check and Replace Sensors

Tools Required: Socket set, screwdriver
Inspect the seat belt buckle sensors for proper functionality.
If faulty, remove the old sensor by unscrewing it and disconnecting the wiring connector.
Install the new sensor by reversing the removal steps and ensuring a secure connection.

4. Resetting the SRS Light

Tools Required: OBD-II scanner
Reconnect the negative battery terminal.
Use the OBD-II scanner to clear any stored DTCs from the SRS system.
Start the vehicle and monitor the dashboard for the SRS light.