how to fix P0135 O2 sensor code on Toyota Highlander Third Generation (2014-2019)

Toyota Highlander Third Generation (2014-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

Error Code: P0135

3 min read

502 words

Problem Statement

Learn how to diagnose and fix P0135 O2 sensor code on Toyota Highlander (2014-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0135

Affected Component

Exhaust System

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working on the exhaust system.

Symptoms

•Check engine light illuminated
•Decreased fuel efficiency
•Rough engine idle
•Engine stalling during acceleration
•Increased exhaust emissions

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0135.
2
Inspect the O2 sensor wiring harness for any visible damage or corrosion.
3
Check the O2 sensor connector for secure fitment and corrosion.
4
Verify the sensor's voltage output using a multimeter.
5
Inspect the vehicle’s exhaust system for leaks near the O2 sensor.
6
Check the vehicle's air-fuel ratio and fuel pressure to ensure they are within specification.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set (22mm O2 sensor socket recommended)
•Torque wrench
•Multimeter
•Wire brush

Parts Required

•New upstream O2 sensor
•Anti-seize compound (if not included with the sensor)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to confirm P0135.
2
Inspect the O2 sensor wiring harness for any visible damage or corrosion.
3
Check the O2 sensor connector for secure fitment and corrosion.
4
Verify the sensor's voltage output using a multimeter.
5
Inspect the vehicle’s exhaust system for leaks near the O2 sensor.
6
Check the vehicle's air-fuel ratio and fuel pressure to ensure they are within specification.

Solution

1. Preparation

Gather tools and parts required.
Park the vehicle on a flat surface and ensure the engine is cool.
Disconnect the negative battery terminal to avoid electrical shock.

2. Remove the Oxygen Sensor

Locate the upstream O2 sensor (typically found on the exhaust manifold).
Use a socket wrench (22mm O2 sensor socket recommended) to carefully unscrew the O2 sensor.
Disconnect the electrical connector from the O2 sensor by pressing the release tab.

3. Inspect and Clean

Inspect the threads of the O2 sensor and the exhaust manifold for carbon deposits and rust.
Clean the threads with a wire brush if necessary.

4. Install New Oxygen Sensor

Apply anti-seize compound (if required) to the threads of the new O2 sensor to facilitate future removal.
Screw the new O2 sensor into the exhaust manifold and tighten to manufacturer specifications (usually around 30 ft-lbs).
Reconnect the electrical connector securely.

5. Reset the Engine Control Module (ECM)

Reconnect the negative battery terminal.
Use the OBD-II scanner to clear the P0135 code from the ECM.
Start the engine and let it run for a few minutes to ensure proper operation.