my Toyota Corolla E170 (2013-2019) makes a grinding noise when I turn, what's wrong?

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

414 words

Problem Statement

Learn how to diagnose and fix grinding noise when turning in Toyota Corolla E170. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Ensure the vehicle is securely lifted and supported on jack stands before working underneath.

Symptoms

•Grinding noise during turns
•Vibration felt in the steering wheel
•Difficulty steering or increased resistance
•Uneven tire wear
•Fluid leaks around steering components

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage to the CV joints or boots.
3
Examine the wheel bearings for play or roughness.
4
Inspect the tie rod ends and control arm bushings for wear.
5
Lift the vehicle and rotate the wheels by hand to listen for grinding noises.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Bearing puller
•Pliers
•Screwdriver set

Parts Required

•Power steering fluid
•CV joint
•Wheel bearings
•Tie rod ends

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Gather tools and parts required.
Ensure the vehicle is parked on a flat surface and the ignition is off.
Disconnect the battery to avoid any electrical issues.

2. Inspect and Replace Power Steering Fluid

Sub-steps:
1. Locate the power steering fluid reservoir.
2. Check the fluid level; if low, fill with the recommended type of power steering fluid (usually Dexron II or III).
3. If the fluid is dark or contaminated, drain and replace it.

3. Check and Replace CV Joints

Sub-steps:
1. Inspect the CV joint boots for tears or leaks.
2. If damaged, remove the wheel and axle nut using a socket set.
3. Disconnect the lower control arm and remove the CV joint from the transmission.
4. Replace with a new CV joint and reassemble the components in reverse order.

4. Replace Wheel Bearings if Necessary

Sub-steps:
1. Remove the wheel and brake assembly.
2. Using a bearing puller, remove the old wheel bearing.
3. Install the new bearing and reassemble the brake assembly and wheel.

5. Tighten or Replace Tie Rod Ends

Sub-steps:
1. Inspect tie rod ends for play or damage.
2. If worn, remove the cotter pin and loosen the nut.
3. Remove the tie rod end from the steering knuckle.
4. Install the new tie rod end and torque the nut to manufacturer's specifications.

Tools Required:

Socket set
Torque wrench
Bearing puller
Pliers
Screwdriver set

Parts Required:

Power steering fluid
CV joint
Wheel bearings
Tie rod ends

Estimated Repair Time: 2-4 hours

Safety Warnings:

Disconnect battery before working on electrical systems.
Ensure the vehicle is securely lifted and supported on jack stands before working underneath.