FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
my Toyota Corolla E170 (2013-2019) has low oil pressure what steps to take - Toyota Corolla
Home/Cars/Toyota/Corolla/E170 (2013-2019)/my Toyota Corolla E170 (2013-2019) has low oil pressure what steps to take

my Toyota Corolla E170 (2013-2019) has low oil pressure what steps to take

Toyota Corolla E170 (2013-2019)

Error Codes
2-4 hours
Time
medium
Difficulty
high
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
4 min read
613 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix low oil pressure in Toyota Corolla E170 (2013-2019). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component
Engine
Estimated Time
2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

  • •Disconnect the battery before working on electrical systems.
  • •Allow the engine to cool before opening the oil drain plug.
  • •Always wear safety glasses and gloves when handling oil and engine components.

Symptoms

  • •Check engine light illuminated
  • •Oil pressure warning light active on the dashboard
  • •Engine noise (ticking or knocking)
  • •Decreased engine performance
  • •Increased oil consumption
  • •Oil leaks under the vehicle

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •OBD-II scanner
  • •Oil pressure gauge
  • •Socket set
  • •Oil filter wrench
  • •Torque wrench
  • •Oil drain pan

Parts Required

  • •Engine oil (0W-20)
  • •Oil filter
  • •Oil pump (if replacement is necessary)
  • •Gasket for oil pan (if removed)

Additional Information

Affected Component
Engine
Estimated Time
2-4 hours
Difficulty
medium
Severity
high
Tools Required
6 items
Parts Required
4 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation
Solution
1. Preparation
  • Gather necessary tools and parts.
  • Ensure the vehicle is parked on a level surface and the engine is cool.
  • Disconnect the battery to avoid any electrical mishaps.
2. Change Oil and Filter

  1. Drain Old Oil:

    • Place an oil drain pan under the oil pan.
    • Remove the oil drain plug using a socket wrench and let the oil drain completely.
    • Replace the drain plug and torque it to the manufacturer’s specification (typically 25-30 ft-lbs).

  2. Remove Oil Filter:

    • Use an oil filter wrench to remove the old oil filter. Ensure the rubber O-ring comes off with it.
    • Lubricate the O-ring of the new oil filter with a small amount of new oil.

  3. Install New Oil Filter:

    • Install the new oil filter by hand, tightening it until snug, then an additional 3/4 turn.

  4. Add New Engine Oil:

    • Refer to the owner's manual for the correct oil type (typically 0W-20) and capacity (about 4.5 quarts).
    • Pour new oil into the engine through the oil filler cap.
3. Inspect and Replace Oil Pump (if necessary)

  1. Remove Timing Cover:

    • Drain coolant and remove components obstructing access to the timing cover.
    • Remove the timing cover bolts and gently pry off the cover.

  2. Access Oil Pump:

    • Remove the oil pan by unbolting and carefully separating it from the engine block.
    • Locate the oil pump and inspect for damage or wear.

  3. Replace Oil Pump:

    • If faulty, unbolt the oil pump from its mounting location.
    • Install the new oil pump, ensuring the oil pump pickup tube is properly positioned.
    • Reinstall the oil pan with a new gasket and torque bolts to specifications.