my Toyota Corolla E170 (2013-2019) AC is blowing warm air why

Toyota Corolla E170 (2013-2019)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

500 words

Problem Statement

Learn how to diagnose and fix AC blowing warm air in Toyota Corolla E170 (2013-2019). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Use caution when handling refrigerant; avoid skin contact and inhalation.

Symptoms

•AC compressor not engaging
•Warm air blowing from vents
•Unusual noises from the AC system
•Reduced airflow from the vents
•AC warning light illuminated on the dashboard

Diagnostic Steps

1
Check the AC control settings to ensure it's set to the correct mode (cooling).
2
Inspect the AC compressor for signs of damage or leaks.
3
Use an OBD-II scanner to check for any error codes related to the AC system.
4
Measure the refrigerant levels using a refrigerant gauge.
5
Inspect the AC fuse in the fuse box for any blown fuses.
6
Check for any blockages or damage to the condenser or evaporator.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Refrigerant gauge
•Manifold gauge set
•Socket set
•Torque wrench
•Screwdriver set

Parts Required

•Refrigerant (R134a)
•AC compressor (if damaged)
•AC fuse (if blown)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the AC control settings to ensure it's set to the correct mode (cooling).
2
Inspect the AC compressor for signs of damage or leaks.
3
Use an OBD-II scanner to check for any error codes related to the AC system.
4
Measure the refrigerant levels using a refrigerant gauge.
5
Inspect the AC fuse in the fuse box for any blown fuses.
6
Check for any blockages or damage to the condenser or evaporator.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is turned off.
Disconnect the negative battery terminal to prevent electrical issues.

2. Recharge Refrigerant

Tools Required: Refrigerant gauge, refrigerant canister, manifold gauge set.
Connect the low-pressure side of the manifold gauge to the low service port on the AC system.
Check the current refrigerant level. If low, proceed to add refrigerant.
Follow the instructions on the refrigerant canister to add refrigerant until it reaches the appropriate level.
Disconnect the manifold gauge and replace the service port cap.

3. Repair or Replace AC Components

Tools Required: Socket set, torque wrench, screwdriver set.
If the compressor is damaged, remove the old compressor by disconnecting the electrical connector and refrigerant lines.
Install the new compressor by reversing the removal steps, ensuring all connections are secure and torqued to manufacturer specifications.
If a blown fuse was found, replace it with a new fuse of the same amperage.

4. Test and Inspect

Reconnect the negative battery terminal.
Start the engine and turn on the AC to check if cold air is blowing.
Monitor for any unusual noises or leaks around the AC components.