How to fix transmission slipping Toyota Corolla

Toyota Corolla E170 (2013-2019)

Error Codes

3-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700, P0730

3 min read

576 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and repair transmission slipping issues in a Toyota Corolla E170 (2013-2019) with this comprehensive guide.

Error Code

P0700, P0730

Affected Component

transmission

Estimated Time

3-4 hours

Symptoms

•Delayed or unresponsive acceleration
•Unusual noises
•Burning smell
•Gear shifting issues
•Check engine light

Diagnostic Steps

1
Connect an OBD-II scanner to the diagnostic port and retrieve error codes.
2
Inspect transmission fluid level and condition.
3
Examine for leaks under the vehicle and around the transmission.
4
Conduct a test drive to confirm symptoms.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II Scanner
•Transmission Fluid Dipstick
•Clean Rags
•Jack and Jack Stands

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

Transmission slipping in a Toyota Corolla E170 (2013-2019) can manifest as delayed acceleration, engine revving without corresponding speed increase, or abrupt gear changes. Below is a detailed guide to diagnose and fix this issue.

Tools Required

OBD-II Scanner
Transmission Fluid Dipstick
Clean Rags
Jack and Jack Stands (if necessary)

Step 1: Check for Error Codes

Connect an OBD-II scanner to the diagnostic port beneath the dashboard.
Retrieve any stored codes related to transmission issues (e.g., P0700, P0730, etc.).
Note down these codes for further investigation.

Step 2: Inspect Transmission Fluid

Locate the Dipstick: With the engine running and the vehicle in park, locate the transmission fluid dipstick.
Check Fluid Level: Pull out the dipstick, wipe it clean, then reinsert and pull it out again to check the fluid level.
- Low Fluid: Can cause slipping. If low, add the recommended type of transmission fluid (Toyota ATF WS).
- Fluid Condition: Fluid should be bright red and not smell burnt. If dark or burnt, a fluid change is recommended.

Step 3: Examine for Leaks

Visual Inspection: Check under the vehicle and around the transmission for any signs of fluid leakage.
Inspect Seals and Gaskets: Look at common leak points like the transmission pan, axle seals, and cooler lines.

Step 4: Test Drive

Conduct a test drive to confirm the symptoms and note specific conditions under which slipping occurs (e.g., during acceleration, uphill, etc.).

Repair Instructions

Step 1: Transmission Fluid Replacement

Warm Up the Vehicle: Drive the car to warm up the transmission fluid.
Raise the Vehicle: Use a jack and jack stands to safely elevate the vehicle.
Drain Old Fluid: Place a drain pan under the transmission pan, remove the drain plug, and let the fluid drain completely.
Replace Transmission Filter: If applicable, remove the transmission pan, replace the filter, and reinstall the pan with a new gasket.
Refill Transmission Fluid: Add new fluid through the dipstick tube, matching the old fluid quantity or as specified in the owner’s manual.
Check Level: Start the engine, let it reach operating temperature, then check and adjust the fluid level as needed.

Step 2: Address Leaks

Seal Replacement: If leaks are identified, replace faulty seals or gaskets.
Tighten Connections: Ensure all connections and bolts are tightened to correct specifications.

Step 3: Reprogram or Replace Transmission Control Module (TCM)

If diagnostic codes indicate TCM issues, consider reprogramming or replacing the TCM following manufacturer guidelines.

Final Check

Re-check Fluid Levels: After a few days of driving, recheck fluid levels to ensure they remain stable.
Monitor Performance: Continue to monitor the vehicle’s performance for any further signs of slipping or issues.

If slipping persists after following these steps, further inspection by a professional may be necessary, as internal transmission components such as clutches or bands may be worn and require rebuilding or replacement.