FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
How do I fix a malfunctioning rearview camera in my 2018 Toyota Camry XV70? - Toyota Camry
Home/Cars/Toyota/Camry/XV70 (2018-2024)/How do I fix a malfunctioning rearview camera in my 2018 Toyota Camry XV70?

How do I fix a malfunctioning rearview camera in my 2018 Toyota Camry XV70?

Toyota Camry XV70 (2018-2024)

Error Codes
2-3 hours
Time
medium
Difficulty
medium
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
3 min read
574 words

Problem Statement

Learn how to diagnose and repair a malfunctioning rearview camera in your 2018 Toyota Camry XV70 with step-by-step instructions and required tools.

Affected Component
rearview camera
Estimated Time
2-3 hours

Symptoms

  • •No Image Displayed
  • •Distorted Image
  • •Error Message
  • •Camera Activation Delay

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •OBD-II scanner
  • •Multimeter
  • •Screwdrivers (Phillips and flathead)
  • •Torx Bit Set
  • •Trim removal tools
  • •Electrical contact cleaner
  • •Replacement camera (if necessary)

Additional Information

Affected Component
rearview camera
Estimated Time
2-3 hours
Difficulty
medium
Severity
medium
Tools Required
7 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation
Fixing a Malfunctioning Rearview Camera in a 2018 Toyota Camry XV70
Tools Required
  • OBD-II scanner
  • Multimeter
  • Screwdrivers (Phillips and flathead)
  • Torx Bit Set
  • Trim removal tools
  • Electrical contact cleaner
  • Replacement camera (if necessary)
Repair Instructions

Step 1: Visual Inspection

  1. Clean the Camera Lens:

    • Use a soft microfiber cloth to clean the lens if dirty.

  2. Inspect Wiring:

    • Remove the rear bumper cover if necessary (refer to the service manual for proper removal procedure).
    • Check the wiring harness connected to the camera for any signs of fraying or disconnection.

Step 2: Check Camera Settings

  1. Access Infotainment System:
    • Start the vehicle and access the settings menu on the display.
    • Navigate to the rearview camera settings and ensure it is turned on.

Step 3: Test the Camera

  1. Check Power Supply:
    • With the multimeter, check the voltage at the camera connector while the vehicle is in reverse.
    • Expect to see approximately 12V. If voltage is present, the camera is likely faulty.

Step 4: Scan for DTCs

  1. Connect OBD-II Scanner:
    • Plug in the OBD-II scanner and retrieve any codes related to the rearview camera.
    • Note any codes and reference them for further diagnostics.

Step 5: Replace the Camera (if necessary)

  1. Remove the Old Camera:

    • If the camera is faulty, disconnect the wiring harness and remove the camera from its mount.
    • Use the appropriate tools to remove any screws or clips holding the camera in place.

  2. Install the New Camera:

    • Position the new camera in the same mount.
    • Secure it with screws or clips.
    • Reconnect the wiring harness.

  3. Reassemble the Vehicle:

    • If the bumper cover was removed, reattach it securely.
    • Ensure all clips and screws are fastened properly.

Step 6: Testing

  1. Test the New Camera:
    • Start the vehicle and shift into reverse.
    • Check the display for a clear image from the new rearview camera.
    • Verify that the camera functions correctly and that any guidelines are displayed properly.
Conclusion

If the rearview camera is still malfunctioning after following the above steps, further diagnostics may be necessary, potentially involving the BCM or the infotainment system itself. Consult with a professional technician or refer to Toyota's service manual for advanced troubleshooting procedures.