how to fix the oil consumption issue in Toyota Camry Eighth Generation (2018-present)

Toyota Camry Eighth Generation (2018-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

4 min read

608 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix excessive oil consumption in Toyota Camry (2018-present). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Allow the engine to cool before working on it.
•Disconnect the battery before performing electrical work.

Symptoms

•Engine oil warning light illuminated
•Increased frequency of oil changes needed
•Blue smoke from the exhaust during acceleration
•Engine misfiring or rough idle
•Low oil level on the dipstick without visible leaks
•Poor fuel economy

Diagnostic Steps

1
Check oil level: Inspect the dipstick to confirm oil level and condition.
2
Inspect for leaks: Examine the engine and undercarriage for any signs of oil leaks.
3
Perform a compression test: Test the engine's cylinders to determine if there are any internal leaks.
4
Inspect the PCV system: Check the Positive Crankcase Ventilation (PCV) valve for proper operation.
5
Scan for fault codes: Use an OBD-II scanner to check for any engine-related error codes.
6
Examine the intake system: Look for oil buildup in the intake manifold or throttle body.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Oil filter wrench
•Compression tester
•Socket set
•Torque wrench
•Throttle body cleaner
•Drain pan

Parts Required

•New PCV valve
•Engine oil (0W-20)
•Oil filter (specific to the 2018-present Toyota Camry)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check oil level: Inspect the dipstick to confirm oil level and condition.
2
Inspect for leaks: Examine the engine and undercarriage for any signs of oil leaks.
3
Perform a compression test: Test the engine's cylinders to determine if there are any internal leaks.
4
Inspect the PCV system: Check the Positive Crankcase Ventilation (PCV) valve for proper operation.
5
Scan for fault codes: Use an OBD-II scanner to check for any engine-related error codes.
6
Examine the intake system: Look for oil buildup in the intake manifold or throttle body.

Solution

1. Preparation

Gather tools and parts: Ensure you have all necessary tools and replacement parts ready.
Safety precautions: Park the vehicle on a level surface, engage the parking brake, and disconnect the battery.

2. Replace PCV Valve

Locate the PCV valve: Find the PCV valve on the engine, usually near the valve cover.
Remove the old PCV valve: Disconnect any hoses attached to the valve and pull it out.
Install the new PCV valve: Push the new valve into place and reconnect all hoses securely.

3. Perform an Engine Oil Change

Drain old oil: Place a drain pan under the oil pan, remove the drain plug, and allow old oil to fully drain.
Replace the oil filter: Remove the old oil filter using an oil filter wrench; lubricate the rubber gasket on the new filter and install it.
Add new oil: Reinstall the drain plug and fill the engine with the recommended grade of oil (typically 0W-20 for this model).

4. Conduct a Compression Test

Remove spark plugs: Use a spark plug socket to take out the spark plugs.
Test compression: Insert a compression tester into the spark plug holes and crank the engine to check the compression readings.
Evaluate results: Compare readings across cylinders; replace worn piston rings if compression is low.

5. Inspect and Clean Intake System

Remove the intake manifold: Follow the manufacturer's service manual for specific instructions.
Clean intake components: Use throttle body cleaner to remove carbon deposits from the manifold and throttle body.
Reinstall the intake manifold: Follow torque specifications for reassembly.