How can I resolve the adaptive cruise control not working in a 2020 Toyota Camry?

Toyota Camry Eighth Generation (2018-present)

Error Codes

2-3 hours

Time

medium

Difficulty

medium

Severity

3 min read

587 words

Problem Statement

Learn how to diagnose and fix adaptive cruise control problems in a 2020 Toyota Camry with step-by-step instructions.

Affected Component

adaptive cruise control system

Estimated Time

2-3 hours

Symptoms

•Adaptive cruise control warning light on the dashboard.
•Adaptive cruise control system fails to engage or disengage.
•Inability to set a speed or adjust speed settings.
•Messages displayed on the dashboard indicating a fault in the ACC system.

Diagnostic Steps

1
Visual Inspection: Check for any visible damage to the front bumper or grille area where the radar sensor is located.
2
Ensure that the radar sensor is not obstructed by dirt, snow, or debris.
3
Ignition On/Engine Off: Turn the ignition to the 'ON' position and check for warning lights.
4
Connect the OBD-II scanner to retrieve any stored codes related to the ACC system.
5
Check the owner’s manual for specific information regarding the ACC system.
6
Ensure the brake fluid level is adequate and test the brake pedal switch.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II Scanner
•Brake fluid tester
•Multimeter
•Soft cloth
•Mild cleaning solution
•Screwdrivers
•Replacement brake switch

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Resolving Adaptive Cruise Control Not Working in a 2020 Toyota Camry

Step 1: Initial Inspection

Visual Inspection:
- Check for any visible damage to the front bumper or grille area where the radar sensor is located.
- Ensure that the radar sensor (located behind the Toyota emblem) is not obstructed by dirt, snow, or debris.

Step 2: Check for Warning Lights

Ignition On/Engine Off: Turn the ignition to the "ON" position (do not start the engine).
Dashboard Check: Look for any warning lights or messages related to the adaptive cruise control or safety systems.

Step 3: Scan for Diagnostic Trouble Codes (DTCs)

Tools Required: OBD-II Scanner
Procedure:
- Connect the OBD-II scanner to the vehicle’s OBD-II port (usually located under the dashboard near the driver’s seat).
- Turn on the ignition and retrieve any stored codes.
- Note any codes related to the adaptive cruise control system (e.g., C1530, C1563, etc.).

Step 4: Reviewing the Owner's Manual

Reference: Check the owner’s manual for specific information regarding the ACC system, including possible causes for it not functioning.

Step 5: Assess the Brake System

Tools Required: Brake fluid tester, multimeter (if needed for brake switch testing)
Procedure:
- Ensure the brake fluid level is adequate.
- Test the brake pedal switch to ensure it operates correctly. A faulty brake switch can disable the ACC.

Repair Instructions

Step 1: Clean the Radar Sensor

Tools Required: Soft cloth, mild cleaning solution
Procedure:
- Gently clean the radar sensor area behind the Toyota emblem with a soft cloth and mild cleaning solution. Ensure there is no dirt or obstruction.

Step 2: Fix or Replace Brake Switch

Tools Required: Screwdrivers, multimeter (for testing), replacement brake switch (if necessary).
Procedure:
- Locate the brake switch, usually found above the brake pedal.
- Disconnect the wiring harness from the brake switch.
- Use the multimeter to test the switch. It should show continuity when the brake pedal is pressed.
- If the switch is faulty, remove it and replace it with a new one.
- Reconnect the wiring harness and test the ACC functionality.

Step 3: Clear Diagnostic Codes

Tools Required: OBD-II scanner
Procedure:
- Once repairs are made, use the OBD-II scanner to clear any stored codes.
- Turn the ignition off and then start the engine to see if the ACC system functions properly.

Step 4: Software Update (if necessary)

Tools Required: Access to a Toyota dealership or a qualified repair facility.
Procedure:
- If the ACC system still does not work, inquire at a dealership about potential software updates for the vehicle’s ECU that may address ACC issues.

Step 5: Final Testing

Test Drive: Take the vehicle for a test drive to ensure the adaptive cruise control system is functioning as expected.
Monitor: Keep an eye on the dashboard for any warning lights during the test drive.

Conclusion

If the adaptive cruise control system still does not work after following these steps, further diagnostics may be required by a qualified technician, potentially involving more in-depth electrical or mechanical checks of the ACC system components.