How can I fix the rearview camera not displaying in a 2020 Toyota Camry?

Toyota Camry Eighth Generation (2018-present)

Error Codes

2-3 hours

Time

medium

Difficulty

medium

Severity

4 min read

701 words

Problem Statement

Learn how to troubleshoot and fix the rearview camera not displaying issue in a 2020 Toyota Camry with step-by-step diagnostic and repair instructions.

Affected Component

rearview camera system

Estimated Time

2-3 hours

Symptoms

•Rearview camera display is blank or not activating when the vehicle is in reverse.
•Display may show a 'Camera Unavailable' message.
•Camera image may be distorted or frozen.

Diagnostic Steps

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Screwdrivers (Phillips and flat-head)
•Trim removal tools
•Electrical contact cleaner
•Basic hand tools (wrenches, pliers)
•Safety gloves and goggles

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Fixing Rearview Camera Not Displaying in a 2020 Toyota Camry (XV70)

Tools Required

OBD-II scanner
Multimeter
Screwdrivers (Phillips and flat-head)
Trim removal tools
Electrical contact cleaner
Basic hand tools (wrenches, pliers)
Safety gloves and goggles

Repair Instructions

Step 1: Check Settings and Gear Position

Start the vehicle and shift it into reverse.
Observe the infotainment screen to see if the camera activates.
If not, check the settings in the multimedia system to ensure the camera feature is enabled.

Step 2: Visual Inspection

Inspect the Camera:
- Locate the rearview camera above the license plate area.
- Clean the camera lens with a soft cloth to remove any dirt or debris.
- Look for any physical damage to the camera housing.
Inspect Wiring:
- Use a trim removal tool to gently remove any panels obstructing access to the camera wiring.
- Examine the wiring harness for any signs of damage or loose connections.
- Ensure that the connectors are securely fastened.

Step 3: Test Voltage at Camera

Disconnect the camera from its wiring harness.
Using a multimeter, set it to DC voltage mode.
Connect the positive lead to the camera’s power wire (usually red) and the negative lead to the ground wire (usually black).
While the vehicle is in reverse, check for voltage. You should see approximately 6-12 volts.
- If voltage is present, the camera may be faulty.
- If no voltage is detected, there may be an issue with the wiring or the reverse light circuit.

Step 4: Check and Clear Fault Codes

Connect the OBD-II scanner to the vehicle’s diagnostic port.
Turn the ignition to the ON position (do not start the engine).
Navigate to the diagnostic section and scan for any fault codes.
If any codes related to the camera or electrical systems are present, note them down.
Clear the fault codes and see if the camera activates upon shifting into reverse.

Step 5: Replace the Camera (if necessary)

If the camera is confirmed faulty, remove the old camera.
- Use a screwdriver to unscrew the camera mounting screws.
- Disconnect the wiring harness carefully.
Install the new camera:
- Connect the wiring harness and ensure it clicks into place.
- Secure the new camera into the mounting bracket with screws.
Reassemble any panels or trim that were removed to access the camera.

Step 6: Test the System

Start the vehicle and shift into reverse.
Check if the rearview camera display activates properly.
If the camera is functioning, ensure that all wires and panels are secured.

Conclusion

If the rearview camera is still not displaying after following these steps, consider consulting with a certified Toyota technician, as there may be deeper electronic issues at play. Always ensure that your vehicle’s software is up to date, as updates can sometimes resolve functionality issues.