why does my Renault Clio V lose power when the AC is on?

Renault Clio V (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

564 words

Problem Statement

Discover how to diagnose and resolve power loss issues in Renault Clio V when AC is activated. Step-by-step guide with diagnostic and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening any components.

Symptoms

•Loss of engine power during acceleration
•Reduced responsiveness of the throttle
•Engine stalling or struggling at low RPMs
•Unusual engine noise when AC is engaged
•Increased fuel consumption

Diagnostic Steps

1
Scan the vehicle's onboard diagnostic system using an OBD-II scanner for any error codes.
2
Check the AC system for refrigerant levels and leaks.
3
Inspect the engine air filter for blockages or clogs.
4
Examine the serpentine belt for wear or slippage, particularly under load.
5
Test the battery voltage and alternator output under load conditions.
6
Assess the idle air control valve functionality.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•AC manifold gauge set
•Screwdriver set
•Socket set
•Multimeter

Parts Required

•Replacement air filter
•Refrigerant (if needed)
•Serpentine belt (if necessary)
•Idle air control valve (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's onboard diagnostic system using an OBD-II scanner for any error codes.
2
Check the AC system for refrigerant levels and leaks.
3
Inspect the engine air filter for blockages or clogs.
4
Examine the serpentine belt for wear or slippage, particularly under load.
5
Test the battery voltage and alternator output under load conditions.
6
Assess the idle air control valve functionality.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the battery to ensure safety while working on electrical components.
Allow the engine to cool before beginning any work.

2. Check and Recharge AC System

Tools Required: AC manifold gauge set, refrigerant (if low).
Inspect the refrigerant level using the AC manifold gauge.
If low, recharge the AC system with the appropriate refrigerant as specified by the manufacturer.

3. Inspect and Replace Air Filter

Tools Required: Screwdriver set, replacement air filter.
Remove the air filter housing cover using the screwdriver.
Take out the old air filter and inspect for excessive dirt or clogging.
Install the new air filter, ensuring it fits securely, then replace the housing cover.

4. Inspect Serpentine Belt

Tools Required: Socket set.
Visually inspect the serpentine belt for any signs of wear, cracks, or slippage.
If damaged, remove the belt by loosening the tensioner with a socket and replacing it with a new belt, ensuring correct routing.

5. Test Battery and Alternator

Tools Required: Multimeter.
Connect the multimeter to the battery terminals and check for a voltage reading above 12.6 volts when the engine is off and around 13.7-14.7 volts when the engine is running.
If the voltage is low, consider replacing the battery or alternator as necessary.

6. Check Idle Air Control Valve

Tools Required: Cleaning solvent, screwdriver, replacement IAC valve if necessary.
Locate the idle air control valve and remove it for inspection.
Clean the valve with a suitable solvent, then reattach it.
If cleaning does not resolve issues, replace the valve with a new one.