how to fix wheel bearing noise in Honda CR-V Fifth Generation (2017-2022)

Honda CR-V 6th Gen (2023-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

557 words

Problem Statement

Learn how to diagnose and fix wheel bearing noise in Honda CR-V Fifth Generation (2017-2022). Step-by-step guide with tools and procedures included.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the brakes to cool before handling.

Symptoms

•Continuous humming or grinding noise while driving
•Noise increases with vehicle speed
•Vibration felt in the steering wheel
•Uneven tire wear
•Loose or wobbly wheel movement when checked

Diagnostic Steps

1
Conduct a visual inspection of the wheel bearings for any visible damage or rust.
2
Drive the vehicle and listen for changes in noise when turning left or right, which may indicate which bearing is affected.
3
Check for play in the wheel by lifting the vehicle and shaking the wheel at the 12 o’clock and 6 o’clock positions.
4
Inspect the brake components and dust shields for interference or damage.
5
Use a stethoscope or a long screwdriver to pinpoint the source of the noise by placing it against the wheel hub.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Hub puller
•Brake cleaner
•Hydraulic press

Parts Required

•Replacement wheel bearing
•Brake rotor (if worn)
•Brake pads (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Conduct a visual inspection of the wheel bearings for any visible damage or rust.
2
Drive the vehicle and listen for changes in noise when turning left or right, which may indicate which bearing is affected.
3
Check for play in the wheel by lifting the vehicle and shaking the wheel at the 12 o’clock and 6 o’clock positions.
4
Inspect the brake components and dust shields for interference or damage.
5
Use a stethoscope or a long screwdriver to pinpoint the source of the noise by placing it against the wheel hub.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is off.
Safety gear: wear gloves and safety glasses.

2. Lift the Vehicle

Use a jack to lift the vehicle and secure it with jack stands.
Remove the wheel covering the affected bearing.

3. Remove the Brake Caliper

Use a socket set to remove the bolts securing the brake caliper.
Hang the caliper using a wire to avoid straining the brake line.
Remove the brake rotor by unscrewing any retaining screws if present.

4. Remove the Wheel Hub Assembly

Remove the axle nut using a socket wrench.
Disconnect any ABS sensor wiring if applicable.
Remove the bolts securing the wheel hub assembly to the steering knuckle.
Use a hub puller if necessary to detach the hub from the knuckle.

5. Replace the Wheel Bearing

Press out the old bearing from the hub using a hydraulic press.
Clean the hub area and press in the new bearing, ensuring it is properly seated.
Reassemble the hub assembly onto the steering knuckle with new bolts if required.

6. Reassemble the Brake Components

Reinstall the brake rotor and caliper, tightening bolts to the manufacturer's specified torque.
Reconnect any ABS sensor wiring.

7. Reinstall the Wheel

Place the wheel back onto the hub and hand-tighten the lug nuts.
Lower the vehicle and torque the lug nuts to the manufacturer’s specifications.