why is my Honda CR-V Fifth Generation (2017-2022) making a grinding noise when I brake

Honda CR-V Fifth Generation (2017-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

435 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix grinding noise when braking in Honda CR-V Fifth Generation (2017-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always allow brakes to cool before inspecting.
•Disconnect the battery before working on electrical components related to ABS.

Symptoms

•Grinding noise when applying brakes
•Reduced braking efficiency
•Pulsating brake pedal
•Vibration in the steering wheel during braking
•Brake warning light illuminated on the dashboard

Diagnostic Steps

1
Inspect brake pads for wear and damage.
2
Check brake rotors for scoring or warping.
3
Examine brake calipers for proper function and alignment.
4
Inspect brake fluid level and condition.
5
Evaluate the ABS system for faults if applicable.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Brake grease
•Bungee cord

Parts Required

•Brake pads
•Brake rotors (if necessary)
•Brake fluid (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface.
Engage the parking brake and place wheel chocks behind the rear wheels.

2. Remove Wheel

Use a jack to lift the front of the vehicle and secure it with jack stands.
Remove the lug nuts using a socket set and take off the wheel.

3. Inspect and Replace Brake Pads

Remove the caliper bolts using a socket wrench.
Lift the caliper off the rotor and support it with a bungee cord (do not let it hang by the brake line).
Inspect the brake pads for wear. If they are less than 3mm thick or show uneven wear, replace them.
To install new pads, apply brake grease to the backing of the new pads, then insert them into the caliper bracket.

4. Inspect and Replace Brake Rotors

Check the surface of the rotors for scoring or warping.
If damaged, remove the rotor by unscrewing the retaining screws (if applicable) and sliding it off the hub.
Replace with new rotors, ensuring they are properly seated.

5. Reassemble Braking Components

Reattach the caliper over the new pads and rotor, tightening the caliper bolts to the manufacturer’s specified torque (typically between 15-25 ft-lbs).
Reinstall the wheel and hand-tighten the lug nuts.

6. Lower Vehicle and Test

Lower the vehicle from the jack stands.
Torque the lug nuts to the manufacturer’s specifications (generally 80-100 ft-lbs).
Pump the brake pedal several times to ensure proper pad seating before driving.

Tools Required:

Jack and jack stands
Socket set
Torque wrench
Brake grease
Bungee cord

Parts Required:

Brake pads
Brake rotors (if necessary)
Brake fluid (if needed)

Estimated Repair Time: 2-4 hours

Safety Warnings:

Always allow brakes to cool before inspecting.
Disconnect the battery before working on electrical components related to ABS.