how to fix P0700 code Honda Civic 10th Generation (2016-2021)

Honda Civic 10th Generation (2016-2021)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

Error Code: P0700

3 min read

574 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix P0700 transmission control fault in Honda Civic 10th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0700

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow the engine to cool before working on the transmission.

Symptoms

•Check engine light illuminated
•Transmission slipping or harsh shifting
•Delayed engagement when shifting from park to drive
•Loss of power during acceleration
•Unusual noises from the transmission

Diagnostic Steps

1
Scan the vehicle's OBD-II system with a diagnostic scanner to retrieve any additional transmission-related trouble codes.
2
Inspect the transmission fluid level and condition; low or dirty fluid can cause transmission issues.
3
Check the wiring and connectors to the transmission control module (TCM) for any signs of damage or corrosion.
4
Measure the voltage at the TCM using a multimeter to ensure it’s receiving the correct power supply.
5
Perform a road test to replicate the symptoms and observe transmission behavior under various conditions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Multimeter
•Fluid drain pan

Parts Required

•Honda ATF DW-1 transmission fluid
•Transmission filter (if applicable)
•Transmission pan gasket
•Transmission control module (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's OBD-II system with a diagnostic scanner to retrieve any additional transmission-related trouble codes.
2
Inspect the transmission fluid level and condition; low or dirty fluid can cause transmission issues.
3
Check the wiring and connectors to the transmission control module (TCM) for any signs of damage or corrosion.
4
Measure the voltage at the TCM using a multimeter to ensure it’s receiving the correct power supply.
5
Perform a road test to replicate the symptoms and observe transmission behavior under various conditions.

Solution

1. Preparation

Gather tools and parts.
Disconnect the negative battery terminal to prevent electrical shorts.
Shift the vehicle into park and apply the parking brake.

2. Inspect and Replace Transmission Fluid

Locate the transmission fluid dipstick (if equipped) or the fill plug.
Remove the dipstick or fill plug and check the fluid level.
If the fluid is low, add the recommended type of transmission fluid (Honda ATF DW-1).
If the fluid appears dirty or burnt, drain the transmission fluid:
- Place a drain pan under the transmission.
- Remove the transmission pan bolts and the pan.
- Allow the old fluid to drain completely.
- Clean the pan and replace the filter if necessary.
- Reinstall the pan with a new gasket and torque to manufacturer specifications.

3. Inspect and Repair Wiring/Connectors

Visually inspect the wiring harness and connectors related to the TCM.
Look for frayed wires, loose connections, or corrosion.
Repair or replace any damaged wiring or connectors.

4. Replacing the Transmission Control Module (if necessary)

If the TCM is determined to be faulty, remove it:
- Disconnect all electrical connectors from the TCM.
- Remove the mounting bolts securing the TCM to its bracket.
- Install the new TCM by reversing the removal steps.
Reconnect all connectors ensuring they are secure.

5. Reconnect Battery and Clear Codes

Reconnect the negative battery terminal.
Use the OBD-II scanner to clear the P0700 code and any other transmission-related codes.
Perform a test drive to ensure the issue is resolved.