why does my Honda Accord 10th Generation (2018-2022) make a clicking noise when turning

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

528 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is securely lifted and supported before working underneath.
•Allow the engine to cool before inspecting or working around the power steering system.

Symptoms

•Clicking noise present during left or right turns
•Noise intensifies with sharper turns
•Vibration in the steering wheel while turning
•Possible loss of power steering assistance
•No visible fluid leaks around steering components

Diagnostic Steps

1
Inspect the CV joints for any visible damage or excessive wear.
2
Check for play in the wheel bearings by lifting the vehicle and shaking the wheel.
3
Examine the suspension components (control arms, bushings) for any signs of damage or wear.
4
Test the power steering fluid level and condition.
5
Scan for error codes using an OBD-II scanner to check for any related issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Jack and jack stands
•Torque wrench
•OBD-II scanner

Parts Required

•CV joint (if damaged)
•Control arm or bushings (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for any visible damage or excessive wear.
2
Check for play in the wheel bearings by lifting the vehicle and shaking the wheel.
3
Examine the suspension components (control arms, bushings) for any signs of damage or wear.
4
Test the power steering fluid level and condition.
5
Scan for error codes using an OBD-II scanner to check for any related issues.

Solution

1. Preparation

Gather tools and parts for the repair.
Ensure the vehicle is parked on a flat surface, and set the parking brake.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Inspect CV Joints

Sub-step 1: Lift the front of the vehicle using a jack and secure it with jack stands.
Sub-step 2: Remove the front wheels using a socket set.
Sub-step 3: Visually inspect the outer CV joints for torn boots or grease leakage. If damaged, proceed to replace the CV joint.

3. Replace Damaged CV Joint (if applicable)

Sub-step 1: Remove the axle nut using a socket wrench.
Sub-step 2: Detach the lower control arm from the steering knuckle.
Sub-step 3: Pull the axle out of the transmission, being cautious of any fluid leakage.
Sub-step 4: Insert the new CV joint and reassemble in reverse order, ensuring all components are torqued to the manufacturer's specifications (typically around 40-70 ft-lbs for axle nut).

4. Inspect and Replace Suspension Components (if needed)

Sub-step 1: Check control arms and bushings for wear; replace any damaged components.
Sub-step 2: Reinstall the suspension components and torque to specified values.

5. Reassemble and Test

Sub-step 1: Reattach the front wheels and lower the vehicle.
Sub-step 2: Reconnect the negative battery terminal.
Sub-step 3: Start the engine and perform a test drive to verify the clicking noise has been resolved.