my Honda Accord 10th Generation (2018-2022) has a grinding noise when turning, what's the issue?

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

562 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix grinding noise when turning in Honda Accord 10th Generation (2018-2022). Step-by-step guide with symptoms and solutions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Always use jack stands when working under a vehicle.

Symptoms

•Grinding noise when turning the steering wheel
•Difficulty in steering or a feeling of resistance
•Uneven tire wear
•Vibration in the steering wheel
•Clunking sounds when hitting bumps

Diagnostic Steps

1
Inspect the power steering fluid level and condition; top off or replace if necessary.
2
Check for any visible damage or wear on the CV joints and boots.
3
Examine the wheel bearings for play or roughness during manual rotation.
4
Inspect suspension components (control arms, bushings, struts) for damage or wear.
5
Test drive the vehicle to isolate the noise under different turning conditions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Jack and jack stands
•Bearing press
•Turkey baster

Parts Required

•Power steering fluid (Honda PSF)
•CV joint or axle assembly (if damaged)
•Wheel bearings (if worn)
•Suspension components (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition; top off or replace if necessary.
2
Check for any visible damage or wear on the CV joints and boots.
3
Examine the wheel bearings for play or roughness during manual rotation.
4
Inspect suspension components (control arms, bushings, struts) for damage or wear.
5
Test drive the vehicle to isolate the noise under different turning conditions.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Inspect and Replace Power Steering Fluid

Sub-steps:
1. Locate the power steering reservoir and remove the cap.
2. Check fluid level; if low, add the recommended power steering fluid (Honda PSF).
3. If fluid is dirty or contaminated, drain the old fluid using a turkey baster or equivalent.
4. Refill with fresh power steering fluid and replace the cap.

3. Inspect and Replace CV Joints

Sub-steps:
1. Raise the front of the vehicle using a jack and secure it with jack stands.
2. Remove the front wheels using a socket set.
3. Inspect the CV joints and boots for any tears or grease leakage.
4. If damaged, remove the axle nut and slide the axle out of the hub.
5. Replace the CV joint or axle assembly as needed, ensuring to torque the axle nut to manufacturer specifications.

4. Inspect and Replace Wheel Bearings

Sub-steps:
1. With the wheels removed, check for play in the hub assembly.
2. If the bearing is worn, remove the brake caliper and rotor.
3. Unscrew the hub assembly and replace the wheel bearing using a bearing press.
4. Reassemble the hub and ensure all bolts are torqued to specification.

5. Inspect and Replace Suspension Components

Sub-steps:
1. Examine control arms and bushings for wear or damage.
2. If any components are worn, unbolt the damaged part and replace it.
3. Reassemble and torque all bolts to manufacturer specifications.